Bedienungsanleitung Bianco di puro Tune Pro (Seite 25 von 38) (Deutsch)

814571

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

EN EN

10 11

REQUIREMENTS OF THE INSTALLATION LOCATION

ELECTRICAL CONNECTION

For the safe and faultless operation of your Tune Pro, the installation location must fulfil the following condition:

• Connect your Tune Pro to a power outlet with the appropriate electrical ratings. This can be found on the nameplate on

the underside of the motor and in chapter “Technical data” on page 33.

• Make sure that the power plug is properly plugged into the outlet.

• The device must be placed on a level, flat, solid and nonslip surface that ensures the load capacity.

• Take care that the device cannot fall over.

• Do not place a cloth under the device.

• Choose the installation location so that children cannot play with the device or reach into it and cannot pull the

power cord of the device.

• Place the unit only inside and do not operate it outdoors.

• Do not place the device in the immediate vicinity of other heat sources (direct sunlight, oven, stove, etc.).

For the safe and faultless operation of the device, the following points for the electrical connection

must be observed:

• Connect your Tune Pro to a power socket with the correct electric specifications. You can find them on the type plate at

the back side of the device, sea also Chapter „Technical Data“ on page 33. Make sure that the power plug is properly

inserted into the power socket.

• The electrical safety can only be ensured, if it is connected to a properly installed protective earth system.

• The manufacturer takes no responsibility for damages caused by a missing or disconnected protective earth.

• Make sure that the power cable is undamaged and does not pass over hot surfaces or sharp edges.

• The power cable must not be pulled tight or under tension.

• Make sure that the power plug is properly inserted into the power socket, a loose plug can lead to overheating of the

device or electric shock.

OPERATING TUNE PRO

Energy Saving Mode1

The status-indicator flashes red. Without the attached jar your Tune Pro cannot be switched on for safety reasons.

Start up / Activating Standby Mode

For use of your Tune Pro it is necessary that the jar is placed correctly on the motor base and the power cable connected

to a suitable power supply. Now the available options for each function mode light up on the control element. The function

mode depends on the attached jar.

Standby Mode

In standby mode, the mixing programs, the manual mode and the pulse mode can be used.

Refer to page 14 for more information.

MEASURING CUP, LID AND SEAL RING

Place the measuring cup 1 in the opening of the lid 2 and

twist it tight towards the right. Now, place the lid firmly on the

jar. Turn the measuring cup to the left to take it off, and lift it

off the lid.

The silicone seal 3 of the lid can be removed for easier

cleaning. Before you start mixing, pay attention to the

following but make sure that the silicone seal is correctly

fitted to the jar lid was mounted.

Your Tune Pro automatically changes to Energy Saving Mode after 3 Minutes of inactivity.

1 Power consumption in Energy Saving Mode: 0.88 watt

Measuring cup

Deckelönung

Silicone seal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bianco di puro Tune Pro Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info