Bedienungsanleitung Bielmeier BHG52 (Seite 20 von 23) (Deutsch, Englisch)

740639

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

18 19

Step 1 – Holes to drill

Determine the installation height of the hood while observing the minimum clearance to the stove top.

Keyholes „A“ for wall attachment - use 8x80 screws to mount the hood on the wall. Hang the hood body (22)

into both screws (26) with the keyholes „A“. Align the hood body horizontally and tighten screws (26).

Step 2 – Locating dowels and screws

Insert dowels and screw the 2 screws into the holes with the dowels. Only screw in the screws to the point that

you can still hang the hood.

Step 3 – Hanging the hood

Then hang the hood with 2 person to - or onto - the two screws. Verify again that the screws extend far enough

from the wall for hanging on the mounting bracket so that suﬃcient space remains for the mounting rail of the

hood. You can then tighten the screws further.

Step 4 – Install air hose (only for exhaust air mode)

Use a Ø 150 mm plastic pipe or exhaust air hose for the connection with the wall break-through.

Important: The exhaust air hose must be prepared before the extractor hood is mounted.

Cut the pipe or hose to the required length. Do not kink the hose. Connect the pipe/hose with one side on the

adapter ﬂange of the extractor hood and on the exhaust air adapter in the wall with the other side.

Important: If the exhaust air is routed to an exterior wall, the air exhaust must be equipped from the outside with

a cover with self-opening slats or a non-return hatch (not included in supplied scope). Contract this work to the

contractor who installs the wall break-through.

Step 5 – Connecting to an exhaust duct or as direct exhaust

It is essential that the connection is performed correctly when the connection is made to an interior exhaust duct.

right wrong

Step 6 – Installing the chimney

The installation position for the mounting hardware of the chimney. Measure the correct position and mark the

locations for the holes to drill. Center the holes accurately in relation to the hood position since the telescopic

chimney can otherwise not be extended upward in a vertical.

The drill the holes and secure the chimney hardware with the matching dowels and screw.

Remove the protective foil. Assemble the chimney consisting of the base chimney (23) and the telescopic chimney

(24) as follows:

For recirculating air mode: insert the telescopc chimney (24) so that the air exhaust slots point

upward. For exhaust air mode: insert the telescopic chimney (24) with the air exhaust slots pointing down. The air

exhaust slots are then concealed.

Secure the mounting bracket (25) to the wall with two screws 6x80 mm (2). Select the spacing of the mounting

bracket (25) based on the installation sketch or your physical arrangements.

Slide the base chimney (23) with inserted telescopic chimney (24) over the motor block. Now extend the

telescopic chimney (2) up to the room ceiling and secure to the mounting bracket with 6 screws 4 x 6 mm (27).

Step 7 – Startup

After completing the hood installation:

• Remove all cardboard from the hood and pull oﬀ all protective foils from the stainless steel surfaces.

• Conduct a function test (see Section „Operating the hood“).

TECHNICAL SPECIFICATIONS

Voltage: 220 V ~240V

Frequency: 50 Hz

Motor rating: 150W

Number of standard levels: 5

Lighting: 2 x 1.5 W

Total power rating (connected load): 153 W

Current draw: 1.20 A

Protection class: 1

Length of power cable: 1.5 m

Exhaust air connection: Ø150mmLänge Netzanschlusskabel: 1,5 m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bielmeier BHG52 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info