Bedienungsanleitung Bielmeier BHG53 (Seite 15 von 23) (Deutsch, Englisch)

740640

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

8 9

Diameter of exhaust pipe connection: 120 mm

Attach reduction directly on the air ﬂange. Attach exhaust pipes on the reduction ﬂange. Appropriately seal both

connections.

Instructions for recirculating air mode

You can use this hood in recirculating mode directly without using additional parts.

We only recommend using activated carbon ﬁlters to reduce odors.

IMPORTANT: Using an activated carbon ﬁlter integrates additional resistance into the air path, therefore reducing

the airﬂow volume and the ﬂow velocity.

In order to give the odor molecules suﬃcient time to embed themselves into the activated carbon, it is important

to ensure that the airﬂow velocity of the vapor is not excessively high. Running the unit at level 1-2 is therefore

more eﬀective than at level 3 for odor ﬁltration in recirculating air mode.

Only a minor portion of the moisture created during cooking is absorbed by the grease and odor ﬁlter. It is then

important particularly in recirculating air mode to ventilate the kitchen area with a wide open window after

cooking. Ventilation prevents excess moisture generated while cooking from remaining in the room, resulting

in mold growth.

Bielmeier oﬀers special optional recirculation air kits for many models. If available, these kits can be ordered as

accessories directly from Bielmeier. The recirculation air kit provides optimized airﬂow in the chimney and prevents

mold growth and dirt buildup behind the chimney and on the ceiling above the chimney. If interested, please

contact Bielmeier to ﬁnd out if a recirculation air kit is available for your model.

Electrical connection

Before making the electrical connection, it is essential that you review and observe the warnings in the „Safety

Instruction“ section. The extractor hood must only be connected by a qualiﬁed electrician who is familiar with

the regulations of the competent electrical utility.

RISK OF INJURY

If the connecting line of the extractor hood is damaged it will need to be replaced by a trained technician

inorder to avoid hazards. The extractor hood must only be connected to a properly installed, grounded wall

plug. Whenever possible, the grounded wall plug should be installed directly behind the chimney enclosure.

The grounded wall plug should be connected to a dedicated electrical circuit. A disconnect device equivalent

to a hard-wired connection must be used if the grounded wall plug is no longer accessible after installing the

extractor hood.

If a hard-wired connection is required

A disconnect device must be installed. Disconnect devices must be switches with a contact opening of more

than 3 mm and all-pole disconnect. These include LS switches, fuses, and circuit breakers.

This extractor hood meets EU radio interference regulations.

The extractor hood is designed for a wall-mounted installation. You will also need to account for any special

accessories to be installed during the installation. Please note the minimum spacing between the burner and

the extractor hood (see „Safety Instructions“)!

EQUIPMENT CARE INSTRUCTIONS

Risk of injury

The extractor hood needs to be disconnected from power by pulling the power plug or by disabling the breaker

prior to each cleaning and service.

Cleaning equipment surfaces

NOTE: The stainless steel and glass surfaces of the equipment and the operator controls are prone to scratching.

You should therefore be sure to note the following cleaning instructions:

Never clean the hood with dry cloths, abrasive sponges, abrasive agents such as cleaning agents that contain

sand, soda, chloride or other aggressive chemicals.

Use a soft, moist cloth, a household cleaning agent or a very mild window cleaner to clean the equipment

surfaces and operator controls.

Do not scrape oﬀ dried-on dirt; instead, allow it to soak and then wipe oﬀ with a moist cloth.

Ensure that no moisture is allowed to enter the electronics when cleaning the operator controls. Clean to no

more than a ﬁne moisture ﬁlm.

NOTE: Only wipe down stainless steel surfaces in the direction of the ﬁnish grain. Do not use stainless steel clea-

ners for operator controls! Cleaning and care agents suited for stainless steel and glass surfaces can be obtained

from your household supplies dealer.

Metal grease ﬁlters

The included metal grease ﬁlters absorb the grease content in kitchen fumes. These ﬁlters are made from

non-combustible metals, generally aluminum.

FIRE HAZARD

As more grease is collected in the ﬁlters, the risk increases that this grease can ignite. A contaminated ﬁlter also

restricts the function of the extractor hood. Cleaning the metal ﬁlters regularly and proactively will minimize

the ﬁre risk. While cleaning the grease ﬁlters, also remember to remove any grease ﬁlm from accessible housing

components with a moist cloth.

Cleaning the metal grease ﬁlters

In standard household operating conditions (1 to 2 hours daily), it is suﬃcient to clean the metal grease ﬁlters

once per month.

Removing and inserting the metal grease ﬁlters

Disengage the lock and allow the grease ﬁlters to fold down, while supporting the bottom of the grease ﬁlters

with the other hand.

Cleaning in the dishwasher

The metal ﬁlters in your hood are dishwasher-safe (55 °Celsius). This may result in minor discoloration of the metal.

This has no impact on the function of the grease ﬁlters and does not represent a quality defect. Position the ﬁlters

loosely into the dishwasher without bending them.

NOTE: Do not clean heavily contaminated metal ﬁlters together with other dishes.

Bielmeier BHG53 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info