Bedienungsanleitung Bigben PS3 Cyberbike (Seite 8 von 11) (Englisch)

496713

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Adjusting pedal resistance

You can adjust the pedal resistance on your Cyberbike™ using the knob loca-

ted at the base of the handlebar tube.

• Rotate the knob in an anti-clockwise direction (towards the “-”) to decrease

resistance when pedalling.

• Rotate the knob in a clockwise direction (towards the “+” ) to increase resis-

tance when pedalling.

• Pedal resistance can also

be adjusted when pedalling.

4.ADVANCED FUNCTIONS

4.a. Programming:

4.a.I. How to programme the buttons:

• Press the “PROGRAM” button. The LED underneath this button will come on.

• Press the button or the direction that you wish to assign to another button

(e.g. the A button). The LED will start to ash steadily.

• Press the button that you now wish to use (e.g. the B button). The LED will ash

rapidly for 2 seconds before going off.

• Pressing the B button will now carry out the action previously assigned to the

A button.

You can then reprogram any other button or direction as you wish.

4.a.II. Cancelling programming:

• Press the “PROGRAM” button once. The LED will come on.

• Press the programmed button (e.g. the B button). The LED will start to ash

steadily.

• Press the programmed button again (or the «PROGRAM” button). The LED will

ash rapidly for 2 seconds before going off.

• The B button has now reverted to its original function.

4.a.III. Cancelling all programming:

• Press the “START/PAUSE” and “PROGRAM» buttons at the same time and hold

down for 3 seconds. The LED located below the «PROGRAM” button will ash

for 3 seconds.

4.b. Calibrating the handlebar

• Press the «PROGRAM” button + the “Y” button for 3 seconds. The LED located

below the “PROGRAM” button will ash.

• Centre the handlebar.

• Press the “Y” button. The LED located below the “PROGRAM” button will now

ash more rapidly. The central position of the handlebar has now been set.

• Turn the handlebar to the left or right as far as it will go.

• Press the «Y” button. The LED located below the “PROGRAM” button will ash

for 3 seconds before going off. The handlebar calibration process is now

complete.

Restoring the manufacturer’s calibration (default setting):

• Press the “START/PAUSE” + “PROGRAM” buttons and hold down for 3 seconds.

The LED will ash for 3 seconds. The handlebar calibration will revert to its

default setting and any previous programming will be deleted.

4.c. Gamecube™ / Cyberbike™ modes

Use the Gamecube™ mode when you want to play with a Gamecube™/ Wii™

game. When you want to play with your Cyberbike™ game use the Cyber-

bike™ mode.

CONFIGURATION:

The A / B / X / Y / L / R / Z buttons, the directional pad and analog joysticks

carry out the same actions as those on a traditional Gamecube™ controller.

Brake lever: the brake lever sends back the signal from the «B» button, and can

also be reprogrammed.

4.c.I. Gamecube™ mode

In Gamecube™ mode, FORWARD pedalling is the same as pressing the A but-

ton.

In Gamecube™ mode, REVERSE pedalling is the same as pressing the B button.

ENGLISH DEUTSCH ESPAÑOLFRANCAIS NEDERLANDS ITALIANO PORTUGUÊS

CYBERBIKEGAMECUBE

TMTM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bigben PS3 Cyberbike Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info