Bedienungsanleitung Bioland 2005 (Seite 6 von 8) (Englisch)

661284

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

-9- -10-

3. Lay the cuff on the arm as illustrated. Make

certain that the lower edge of the cuff lies

approximately 2 to 3 cm (

4~1

") above the

elbow and that the rubber tube leaves the cuff

on the inner side of the arm.

Important! The mark (about 3 cm long bar)

must lie exactly over the artery which runs

down the inner side of the arm.

4. Tighten the free end of the cuff and close the

cuff with the closer.

5. There must be no free space between the arm

and the cuff as this would influence the result.

Clothing must not restrict the arm. Any piece of

clothing which does (e.g. a pullover) must be

taken off.

6. Secure the cuff with the Velcro closer in such a

way that it lies comfortably and is not too tight.

Lay the arm on the table (palm upwards) so

that the cuff is at the same height as the heart.

Make sure that the tube is not kinked.

7. Remain seated quietly for two minutes before

you begin the measurement.

COMMENT:

If it is not possible to fit the cuff to the left arm, it can also be placed on the right arm.

However all measurements should be made using the same arm for better cross reference.

A FEW SUGGESTIONS BEFORE MEASUREMENT

1. Avoid eating, smoking, and exercising for at least 30 minutes before taking a measurement.

Also rest for at least 15 minutes before taking a reading.

2. Stress raises blood pressure. Avoid taking measurements during stressful

times.

3. You would better apply the cuff on your left upper arm.

4. Measurement should be taken in a quiet place and you should be relaxed, seated position.

Rest your left arm on a table.

5. Remain still and do not talk during the measurement.

6. Keep a record of your blood pressure and pulse for your doctor. Remember, a single

measurement does not provide an accurate indication of your true blood pressure. You

need to take and record several measurements over a period of time. Try to measure

your blood pressure at the same time each day for consistency. Blood pressure

measurements fluctuate considerably.

7. Wait 5-10 minutes between successive measurements.

Waiting allows the engorged blood

vessels to return to normal. You may require more rest time depending on your individual

physical conditions.

HOW TO MEASURE BLOOD PRESSURE

1. Set up the cuff to your upper arm as previous section of "How to use the upper arm cuff".

2. Press the "POWER" button, all icons appear two seconds on DISPLAY, then switch to

measurement mode,and display "0" or last measurement record.

3. Press "START" button to start measurement, the cuff in the strap will automatically inflate.

When the value on LCD increases to around 150-200 (mmHg), and start to release the

air, and

decrease pressure in the cuff automatically when it senses the heart beat, the

mark ( )

will flash on LCD.

2~3cm (

4~1

POWER

SYS

DIA

PULSE

-min

SYS

DIA

PULSE

-min

START

SYS

DIA

PULSE

-min

SYS

DIA

PULSE

-min

SYS

DIA

PULSE

-min

SYS

DIA

PULSE

-min

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bioland 2005 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info