Bedienungsanleitung Bioland 2006 (Seite 7 von 10) (Englisch)

661286

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

2~3cm (3/4~1")

-11- -12-

1. Pass the end of the cuff (with sewn-in rubber

stopper) through the metal stirrup so that a

loop is formed. The Velcro closer must be

facing outwards.(Ignore this step if the cuff

has already been prepared.)

2. Push the cuff over the left upper arm so that

the tube points in the direction of the lower

arm and palm.

3. Lay the cuff on the arm as illustrated. Make

certain that the lower edge of the cuff lies

approximately 2 to 3 cm (3/4~1") above the

elbow and that the rubber tube leaves the

cuff on the inner side of the arm.

Important! The mark (about 3 cm long bar)

must lie exactly over the artery which runs

down the inner side of the arm.

4. Tighten the free end of the cuff and close the

cuff with the closer.

5. There must be no free space between the

arm and the cuff as this would influence the

result. Clothing must not restrict the arm.

Any piece of clothing which does (e.g. a

pullover) must be taken off.

6. Secure the cuff with the Velcro closer in

such a way that it lies comfortably and is

not too tight. Lay the arm on the table

(palm upwards) so that the cuff is at the

same height as the heart. Make sure that

the tube is not kinked.

HOW TO USE THE UPPER ARM CUFF

7. Remain seated quietly for two minutes

before you begin the measurement.

COMMENT:

If it is not possible to fit the cuff to the left arm, it can also be placed on the right

arm. However all measurements should be made using the same arm for better

cross reference.

1. Avoid eating, smoking, and exercising for at least 30 minutes before taking a

measurement. Also rest for at least 15 minutes before taking a reading.

2. Stress raises blood pressure. Avoid taking measurements during stressful

times.

3. You would better apply the cuff on your left upper arm.

4. Measurement should be taken in a quiet place and you should be relaxed,

seated position. Rest your left arm on a table.

5. Remain still and do not talk during the measurement.

6. Keep a record of your blood pressure and pulse for your doctor. Remember,

a single measurement does not provide an accurate indication of your true

blood pressure. You need to take and record several measurements over a

period of time. Try to measure your blood pressure at the same time each day

for consistency. Blood pressure measurements fluctuate considerably.

7. Wait 5-10 minutes between successive measurements. Waiting allows the

engorged blood vessels to return to normal. You may require more rest time

depending on your individual physical conditions

A FEW SUGGESTION BEFORE MEASUREMENT

1. Set up the cuff to your upper arm as previous section of "How to use the upper

arm cuff".

2. Press the " " button, all icons appear

two seconds on DISPLAY, then flashing

of “U1” or “U2”.

HOW TO MEASURE BLOOD PRESSURE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bioland 2006 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info