Bedienungsanleitung Bionaire BASF1516 (Seite 2 von 26) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

711678

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

PLEASEREAD AND SAVE THESE

INSTRUCTIONS

GENERAL DESCRIPTION (SEE FIG. 1)

A Front Grill

B. Fan Blade

C. Securing Screw

D. Grill Mounting Nut

E. Rear Grill

F. Motor Shaft

G. Plastic Sleeve

H. Motor Housing

I. Selector (Speed) Control

J. Oscillation Control

K. Tilt Head Adjustment Knob

L. Fan Head Locking Knob

M. Fan Head's Neck

N. Inner Pole Extension

O. Pole Locking Knob

P. Outer Pole

Q. Additional Short Pole

R. Base Cover

S. Weight

T. Washer

U. T-Shaped Locking Lever

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including the

following:

• Use the fan only for purposes described in the

instruction manual.

• To protect against electrical shock, do not

immerse the fan, plug or cord in water or spray

with liquids.

• Close supervision is necessary when any

appliance is used by or near children.

• Unplug from the electrical outlet when not in

use, when moving the fan from one location to

another, before putting on or taking off parts

and before cleaning.

• Avoid contact with any moving parts.

• Do not operate in the presence of explosive

and/or flammable fumes.

• Do not operate fan until fully assembled with all

parts properly in place.

• To avoid fire hazard, NEVER place the cord

under rugs or any parts near an open flame,

cooking or other heating appliance.

• Ensure that the fan is switched off from the

supply mains before removing the guard.

• Do not operate any appliance with a damaged

cord, plug, after the appliance malfunctions, or

has been dropped/damaged in any manner.

• The use of attachments not recommended or

sold by the appliance manufacturer may cause

hazards.

• Do not use outdoors.

• Do not let the cord hang over the edge of a

table or counter, or come into contact with hot

surfaces.

• To disconnect from the electrical supply, grip

the plug and pull from the wall outlet. DO NOT

pull on the cord.

• Always use on a dry, level surface.

• Do not operate without the fan grills properly in

place.

• This product is intended for household use

ONLY and not for commercial or industrial

applications.

• Should the fan stop working, first check the

fuse in the plug (UK only) or fuse/circuit

breaker at the distribution board is operating,

before contacting the manufacturer or service

agent.

• If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its service

agent or a similarly qualified person in order to

avoid hazard.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

MISSING A PART FOR YOUR FAN?

Please call 0800 052 3615 for assistance.

ASSEMBLYINSTRUCTIONS

Base/Pole assembly

You will need the base cover (R), weight (S),

outer pole (P), washer (T) and T-shaped locking

lever (U).

1. Turn the base cover upside down and place the

weight into the base cover.

2. Insert the threaded end of the T-shaped locking

lever into the hole of the washer, weight and

through the base cover.

3. Whilst holding the base cover and weight with

one hand vertically, connect the outer pole to

the base, sliding the T-shaped locking lever into

the bottom of the outer pole with your other

hand.

4. Turn the T-shaped locking lever clockwise to

securely attach the pole to the base.

5. Set the base on the floor, weight side down.

Fan head assembly

You are now ready to assemble the fan head.

ENGLISH

1. Unscrew grill mounting nut (D), turning counter-

clockwise, before positioning the rear grill (E)

over the motor shaft (F), making certain that the

vertical slots at the top and bottom of the rear

grill fit over the prongs on the motor housing

(H). Make sure that the carry handle is topmost

on the motor assembly.

2. Secure the rear grill (E) in its place using the

rear grill mounting nut (D). Turn this nut

clockwise and tighten firmly.

3. Slide the fan blade (B) onto the motor shaft

(F) through the rear protrusion, removing and

discarding plastic sleeve (G) if included.

Loosen securing screw (C) on side of

protrusion first. Then make sure securing

screw aligns with notch on motor shaft and

tighten. CAUTION: Avoid contact with sharp

end of blades.

4. Centre the front grill (A) by aligning the

Bionaire logo on the logo plate so that it is

horizontal and parallel with the floor. Then

place the bracket at the top over the front and

rear grills with the hole on the bracket going

through the center vertical bar. Affix the other

clips, making sure they go over both the front

and rear grills.

Final assembly

1. Slide the inner pole extension (N) up from the

outer pole (P), first loosening the pole locking

knob (O), to securely hold this position.

Tighten the pole locking knob (O).

2. Place the fan head assembly into this

extension pole, inserting the fan’s head neck

(M) into the pole opening.

3. Add the fan head locking knob (L) to the hole

in the fan head's neck (M), making sure holes

are aligned, and tighten.

NOTE: Fan head locking knob (L) may be in

additional short pole when shipped.

Converting to a table fan

An additional short pole (Q) is supplied which

allows the fan to be converted into a table fan.

To change to this short pole, remove the fan

head assembly from its position on top of the

inner pole extension (N) and unscrew the T-

shaped locking lever (U) at the base. Remove

the outer pole (P), replace with the short pole

(Q) and reassemble as detailed above.

OPERATING INSTRUCTIONS

1. Set the fan base on a dry level surface

2. Make sure the Selector (Speed) Control (H) is

in the OFF(0) position. Selector (Speed)

Control (H) is located on the top of the fan

motor housing.

3. Plug the cord into a suitable 220-240V. AC

outlet.

4. The SPEED is adjusted by turning the Selector

(Speed) Control (H) to the desired setting:

0-1-2-3.

5. The OSCILLATION control (I) is located

on the top of the fan motor housing. To start

oscillation, push the control knob down.

To stop oscillation, pull the control knob up.

ADJUSTMENT

Tiltadjustment

To adjust tilt, loosen the tilt head adjustment

knob (K) and tighten to desired angle.

Heightadjustment

Follow these instructions to adjust the height of

the fan.

1. Turn the pole locking knob (O) counter-

clockwise to loosen the pole.

2. Adjust the pole to the desired height and firmly

tighten the locking knob in a clockwise

direction.

CLEANINGAND MAINTENANCE

Follow these instructions to correctly and safely

care for your Bionaire

fan. Please remember:

• Always unplug the fan before cleaning or

assembly.

• Do not allow water to drip on or into the fan

motor housing.

• Be sure to use a soft cloth, moistened with a

mild soap solution.

• Do not use any of the following as a cleaner:

petrol, thinners or benzene.

Fan blade cleaning

(See instructions for fan head assembly)

1. To access the fan blade, remove the front grill

and securing screw.

2. Clean the fan blade, front and rear grills with

a soft moist cloth.

3. Replace the fan blade, tighten screw and

securely fasten the front grill.

Fan head, base and pole cleaning

Using a soft, moist cloth, with or without a mild

soap solution, carefully clean the fan base, pole

and head. Please use caution around the motor

housing area. Do not allow the motor or other

electrical components to be exposed to water.

FAN STORAGE

Your fan can be stored either partially

disassembled or assembled.

It is important to keep it in a safe, dry location.

• If stored disassembled, we recommend using

the original (or appropriately sized) box.

• If stored assembled or partially assembled,

remember to protect the fan head from dust.

GUARANTEE

Please keep your receipt as this will be required

for any claims under this guarantee.

This appliance is guaranteed for 3 years after

your purchase as described in this document.

During this guaranteed period, if in the unlikely

2 3

Fig.1

MODEL# BASF1516

ABCDEFHIJ

Bionaire BASF1516 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info