Bedienungsanleitung Bionaire BCH9300 (Seite 4 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

711654

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

6 7

Troubleshooting for your Heater

Trouble Probable Cause Solution

• Heater

Does Not

Turn On.

☛

Timer Activated.

☛

Tip-over switch engaged.

☛

Manual user reset is

activated.

☛

Not plugged in properly.

☛

Electrical outlet does not

hold plug in securely.

☛

Thermostat set too low.

☛

Obstruction causing the

heater not to operate.

☛

Circuit breaker trips.

✔

Press the Power Button to turn on the

Heater.

✔

Set heater upright on a level surface and

follow the Tip-over Shut-off instructions to

resume operations.

✔

Follow reset instructions listed in this

manual.

✔

Ensure plug is properly inserted. Make

sure electrical outlet and circuit breaker

are working.

✔

Have outlet replaced by a licensed

electrician.

✔

Press the Thermostat Button to select the

highest temperature setting.

✔

Unplug the heater and remove all

obstructions. Position your heater 0.9m

(36 inches) away from all objects.

✔

Make sure no other high wattage

appliances are operating on the same

circuit and reset breaker if needed.

Trouble Shooting

General Information:

Environmental Factors - There are a number of factors that will affect your desired comfort level.

These factors can include insulation, open or drafty doors and windows, and outside temperature.

Please check and take action if any of these potential problems are affecting your heaters ability to

adequately warm your room.

Supplemental Heat - Portable electric heaters are intended for supplemental heating of the room you

are in and turn down the central heat thermostat. They are not intended to replace central heating

systems.

DO NOT attempt to repair or adjust any electrical or mechanical functions on this

heater. Doing so will void warranty. The inside of the heater contains no user

serviceable parts. All servicing should be performed by qualified personnel only.

Troubleshooting for your Heater

Trouble Probable Cause Solution

• Power Light

is Flashing.

☛

Auto Safety Shut-off system

is activated when there is

potential overheat.

✔

Follow Auto Safety Shut-off instructions to

reset the heater and allow sufficient time

for the heater to cool down before

plugging in again.

• Not Enough

Heat.

☛

Heater is in Low or Fan Only

setting.

☛

Thermostat set too low.

✔

Press the Thermostat Button to select

higher temperature setting.

• Heater

cycles ON

and OFF

frequently.

☛

The thermostat automatically

turns the heater on and off

to maintain selected comfort

level.

☛

Every 10-15 minute the

heater turns on and runs for

a minute.

✔

To make this occur less frequently press

the Thermostat Button to select the

highest setting.

✔

This is normal operation to ensure the

heater is maintaining the room temp

accurately.

• Remote

does not

work

☛

Battery low.

☛

Distance too far.

☛

Control Panel Display dirty.

✔

Change batteries (two AAA batteries,

1.5V).

✔

Remote works up to 6m (20 feet).

✔

Be sure to point remote at control panel

on heater and there are no obstructions.

✔

Make sure display panel is clean.

• Heater is

Blowing

Cold Air.

☛

When the heater is in

Thermostat Mode and

reaches the set temperature

it will automatically perform

a 15 second cool down

(blowing cold air) to ensure

thermostat accuracy.

☛

Unit is in the Fan Only

setting.

☛

Power Button may have

been pressed to turn off the

heater.

✔

Raise the temperature higher.

✔

Press the Thermostat Button to select

higher temperature setting.

✔

Press the Power Button to turn on the

heater.

• Fan Speed

Doesn't

Change.

☛

All heat settings control the

heat output of the heater

and not the fan speed. Fan

runs at the same speed on

all settings.

✔

Run heater with the highest temperature

setting for maximum heat output.

• Unexpected

Noise.

☛

You may hear a popping or

crackling sound as the

heater heats up. This is

normal and safe operation.

Once the heater heats up,

the crackling sound will go

away.

✔

If the noise persists, please contact your

local authorized distributor for Bionaire

appliances.

• Unexpected

Smell.

☛

There may be an odor or

vapor coming from the

heater the first time you use

it or after prolonged or

seasonal storage.

✔

This is normal and is the result of dust or

other debris accumulating on the heating

element. Make sure the heater is in a well

ventilated area and continue running until

the odor or vapor goes away.

BCH9300-050_12MLM1.indd 9-10 5/8/12 11:08 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bionaire BCH9300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info