Solutions. Todos los derechos reservados. Distribuido por Sunbeam Products,
Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton,
Florida 33431.
Printed in China/Impreso en China
HEATER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly into
a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. Use handle when moving
this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3
ft (0.9 m) from the front of the heater and keep them away
from the sides and rear.
4. DO NOT run cord under carpeting. DO NOT cover cord with
throw rugs, runners, or the like. Arrange cord away from
traffic area and where it will not be tripped over.
5. This heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. NEVER locate heater
where it may fall into a bathtub or other water container.
6. Extreme caution is necessary when any heater is used by,
or near children or invalids, and whenever the heater is left
operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not the
cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.
10. DO NOT operate heater with a damaged cord or plug, or
after the heater malfunctions, or has been damaged in any
manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
11. A heater has hot and arcing or sparking parts inside. DO
NOT use it in areas where gasoline, paint, or flammable
liquids are used or stored.
12. Use appliance only for intended household use as described
in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to
persons. The use of attachments not recommended or sold
by the manufacturer may cause hazards.
13. DO NOT use outdoors.
14. To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces like a
bed, where openings may become blocked.
15. To disconnect heater, turn unit Off, then remove plug from
outlet.
16. Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord should be No.
14AWG minimum size and rated not less than 1875 watts.
17. If the heater will not operate, see specific instructions under
Auto Safety Shut-off on resetting the heater.
18. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user serviceable
parts. All servicing should be performed by qualified
personnel only.
19. DISCONTINUE USE IF PLUG OR OUTLET IS HOT.
RECOMMEND OUTLET BE REPLACED IF PLUG OR
OUTLET IS HOT TO TOUCH.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A POLARIZED
PLUG (one blade is wider than the other).
To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet
only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician
to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Amps: 12.5
Wattage: 1500W/ (+ 5% - 10%)
Working Voltage: 120V AC/60 HZ
Bulb Type: (2) 25W max Candelabra Base
Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
ASSEMBLY INSTRUCTIONS
Please make sure to check packaging for parts that
could be used to operate your heater.
This package includes:
1 - Fireplace Heater 2 - Light bulbs
1 - Remote Control 2 - AAA Batteries for Remote Control
1 - Stand 4 - Machine Screws (for stand)
1 - Wall Mount Hardware Kit
Installing Batteries into the Remote:
Before operation, insert 2 “AAA” batteries into the back of
the remote control:
• Do not mix old and new batteries
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries
The remote control for this unit has the capability of
remote will not work through walls.
Bulb Installation:
Unwrap the two 25W Candleabra Bulbs from foam
packaging material and open doors on back of unit with a
flathead screwdriver.
(Front of Heater)
(Back of Heater)
Fig. 2
Fig. 1
KEY TO ICONSREMOTE CONTROL
CONTROL PANEL
On/Off
Thermostat
Timer
Flame Brightness
Sound
Fahrenheit/Celsius
OPERATING INSTRUCTIONS
• There may be an odor coming from the heater the
first time you use it. This is normal during the break-in
period or after long term storage. Make sure the heater
is in a well ventilated area and continue running it until
the smell goes away.
• You may hear a popping or crackling sound as the
heater heats up. This is normal and safe operation.
• The Fireplace Heater can be operated by using the
remote control (Fig. 1) or the control panel (Fig. 2)
located on the top of the unit.
• Place the heater on a rm, level surface or mount on
wall.
• Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
(Front of Heater)
(Back of Heater)
Power On/Off
First button push will illuminate LCD and power light. The
units default settings are: Temperature 80°; Timer OFF;
Flame Brightness HIGH; Sound ON. After turning th unit
Off, the fan will continue to run for 10 seconds to cool unit
down.After all settings are chosen, LCD will go dark.
(Front of Heater)
(Back of Heater)
Thermostat
• Press Thermostat button until desired temperature level
appears on LCD Display. It is recommended to start by
setting the temperature to the highest setting. Note: the
fan will continue to run for flame operation without heat.
• The system now maintains the selected comfort level
by automatically turning the heater ON and OFF. The
Thermostat
(Front of Heater)
(Back of Heater)
cycles ON and OFF with the heater
element as it maintains the programmed temperature.
• When LCD reads 00the heat will turn off but the fan will
continue to run for flame operation.
(Front of Heater)
(Back of Heater)
Timer
You can set the timer to automatically turn the unit off.
Press the Timer button, select between 1 and 12 hours.
Your selection will then be displayed on the LCD
(Front of Heater)
(Back of Heater)
Flame Brightness
There are four flame brightness settings: HIGH, MEDIUM,
LOW, OFF. Press button to select desired brightness.
(Front of Heater)
(Back of Heater)
Sound
Press Sound button to turn crackling sound on or off. The
sound volume can be adjusted to 4 levels and turned off.
Push the button to cycle through. To turn the sound off
immediately hold the sound button for two seconds and
release.
(Front of Heater)
(Back of Heater)
Fahrenheit/Celsius
Press to show temperature in Fahrenheit or Celsius.
Wall Mounting Template
To mount into wall studs
1. Find studs in wall. Studs are typically 16” apart.
2. Cut Mounting Template on dotted line and tape onto wall so
brackets are centered on studs.
3. Use level to make sure template is level. Using a sharp object
such as an awl, mark hole location.
4. Using a Power Driver with Phillips head bit, drive 1.5” screws
through bracket and drywall into wood or metal stud.
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
To mount into drywall
Use toggle bolts for 3/8 - 5/8” thick drywall.
1. Cut Mounting Template on dotted line and tape onto wall. Use level to make sure
template is level and mark wall with a sharp object such as an awl.
2. Drill 3/8” holes at top and bottom of bracket guide in center of studs.
3. A - Align bolts, through bracket holes then thread on Spring Loaded Wings. (Fig. A)
B - Collapse Wings while pushing through hole in wall. (Fig. A)
C - Pull bolt out to secure Toggle Wings against inside of wall (wings spring open
on other side of wall and securely hold bolt and bracket). (Fig. B)
D - Screw bolt in until tight.
Mark for
Drill
Mark for
Drill
Mark for
Drill
Mark for
Drill
10 inches2345678910111213141516
Bracket
Bolt
Toggle
Wall
Drilled
Hole
Wall
Spring
Loaded
Toggle
opens on
inside of
wall
Included for mounting:
4 - 1.5” Phillips head self
tapping screws
4 - toggle bolts
2 - mounting brackets
BRACKET
GUIDE
BRACKET
GUIDE
Note: The mounting hardware included is intended for mounting the heater on 3/8” to 5/8” drywall affixed to wood or metal studs. For your convenience the wall mount brackets are 16”
on center to align with 2 studs. Not all studs will be 16” on center. If you are not able to align with studs, toggle bolts are provided. For other wall types, please consult a professional or visit
your local hardware store to determine which type of hardware is best for your particular wall.
Fig. B
Fig. A
Stand Assembly:
For floor use attach the Stand to the Fireplace heater
using the 4 machine screws (provided). Gently lay the unit
on the floor and attach the Stand to the bottom. For wall
mount see Wall Mount Instructions below.
Wall Mount Installation:
This product weighs 25 lbs. Do not install alone.
Mounting Template with instructions is attached below to
make mounting your Fireplace Heater easy.
• Wall Mount Hardware Kit includes:
4 - 1.5” Phillips head self tapping screws
4 - toggle bolts
2 - mounting brackets
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
Max height of 47” (1.2m)
Make sure you allow at least 3 feet of space on sides
of unit.
1. Remove stand from main unit, if installed.
2. Secure the mounting brackets to the wall using the Wall
Mounting Template provided (see below).
3. Hang main body on wall brackets by lifting over the
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Bionaire BFH5000 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
