2 3
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating,
do not cover the heater ( ) Reference to
product.
3. DO NOT position the heater directly under a
power socket.
4. DO NOT use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged,it must
be replacedby the manufacturer or itsservice
agent or similarly qualified person in order to
avoid hazard.The heater contains no user
serviceable parts. Should the product suffer
damageor breakdown, it mustbe returned to
the manufacturer ortheir service agent.
6. Under the environment with electrical fast
transient, the product may malfunction.
7. DO NOT use this heater with a
programmer, timer or any other device
that switches the heater on automatically,
since a fire risk exists if the heater is
covered or positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10.DO NOT position where it can be touched by
children, especially the very young.
11. Allow a safe area around the heater away
from furniture or other objects; at least 50
cm from the top and sides and 200 cm at
the front. The heater is to be placed at least
3m from water source.
12.DO NOT use this heater when it is lying on
its side.
13.DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using,
oxygen, inflammable glue or solvent (e.g.
when gluing or varnishing parquet floors,
PVC etc.)
14.DO NOT insert any objects into the heater.
15.Keep the mains cord at a safe distance from
the main body of the heater.
16.If overheating should occur, the built-in
overheating safety device will switch off
the heater.
17.DO NOT place the cord under a rug.
18.The heater cannot be used adjacent to
curtains or combustible material. Curtains or
combustible material may be burned if the
heater was installed incorrectly.
19.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
20.This heater is filled with a precise quantity of
special oil. Repairs requiring opening of the
oil container are only to be made by the
manufacturer or his service agent who
should be contacted if there is an oil leak;
21 when scrapping the heater, follow the
regulations concerning the disposal of oil.
DESCRIPTIONS (See Fig. 1, 2 & 3)
A. Heated Fins
B. Vents
C.Handle
D.Front Panel
E. Cord Storage
F. Power Cord
G.Front Stand
H.Control Knob
I. Power Light
J. Thermostat Knob
K. Q Shape Screw
L. Casters
M.Foot Plate
N.Wing Nut
O.U-bolt
Technical Specifications
BOH1501/W
Wattage: 1500W
BOH2001/W
Wattage: 2000W
ASSEMBLY INSTRUCTIONS (See Fig. 3)
Please make sure the heater has not been
plugged into any electricity outlet.
Carefully remove heater from box. Some
acessories are packed internally. Please make
sure you have all of the following acessories
prior to throwing away packaging.
1 FootPlate with 2casters (M&L), 1FrontStand (G),
and 1Q shapeScrew (K) and1 Wing Nut(N).
Note: This unit is for FLOOR USE ONLY.
1. Turn the heater upside down and you will see
one U-bolt (O) with wing nut over the last joint
of the heater.
ENGLISH
2. Unscrew the wing nut (N) from the U-bolt (O).
3. Place one hole of the foot plate (M) to the L
shape of the U-bolt (O) and the other hole of
the foot plate into the other end of the U-bolt,
then screw on the wing nut (N).
4. Place the front stand (G) on the bottom of the
radiators front panel, and secure it with the Q
shape screw (K). This front stand (G) is not
meant to be removed once it is attached to
the bottom of the unit.
5. Afterinstallationofthe front stand (G) and foot
plate (M) withcasters(L) turn theheater the
right way up: the heaterisnow ready for use.
OPERATING INSTRUCTIONS
(See Fig. 1&2)
1. Set the unit to the OFF (O) position.
2. Plug in heater. The Power Light (I) will
illuminate and remain lit until the heater
is unplugged.
3. Setthe ThermostatKnob(J)alltheway to
theright.
4.TurntheControlKnob(H) to desiredlevelofheat.
NOTE: When the heater is in use, it is
normal that the heater cycles ON and OFF,
this is to maintain your desired temperature.
After using the heater, turn the Control Knob (H)
to “0” position, turn the Thermostat Knob (J) to
lowest temperature position and unplug the
heater from the socket.
Turn the Control Knob to desired heat setting.
BOH1501/W: 1 -600W, 2 -900W, 3-1500W
BOH2001/W: 1 -800W, 2 -1200W, 3 -2000W
SETTING THE THERMOSTAT
1. Set the Thermostat control all the way to max.
2. When the desired temperature/comfort level is
reached, turn the thermostat control
anti-clockwise to lower position or until the
heater stops operating.
3. The control will now automatically maintain
the pre-set temperature level by turning the
heater ON and OFF.
NOTE: The Power light will remain lit during
operation.
NOTE: It is normal for the heater to cycle ON
and OFF as it maintains the preset
temperature.
ANTI-FROST GUARD INSTRUCTION
If you plug in the heater, it will start working at the
lowesttemperature setting (When thermostat
control is in the lowest temperature position, the
temperature will bemaintained at 5° C, thus the
heaterwill be in the off status unless the room
temperature islower than 5°C. If the room
temperature islower than 5°C, the heaterwill
automatically start working and will keep turning
on & offall the time,maintaining its ambient
temperature of5° C.
NOTE: Unit must be unplugged for it to be
fully off
TIP OVER PROTECTION
When the unit is accidentally knocked over, or
tilts on one side at more than a 45° angle; it
will instantly shut off. To reset, simply place the
heater in an upright position.
STORAGE TIPS
If the heater is not required for long periods, for
example during the summer, it should be stored
at room temperature; in a dry place and
preferably covered to prevent the accumulation
of dust and dirt.
FITTING A REPLACEMENT PLUG FOR
U.K. AND IRELAND ONLY.
If the plug is not suitable for the socket outlets in
your home, it can be removed and replaced by a
plug of the correct type. For correct type and
correct installation please refer to "Installation of
a plug" below.
INSTALLATION OF A PLUG – Applicable to
U.K. and Ireland.
NOTE: If you are in any doubt about wiring
and the installation of the plug. Please
contact a qualified electrician.
NOTE: If a 13A 3-pin plug is fitted, it must be
an ASTA approved plug, conforming to the
BS1363 standard. Replacement 13 amp fuse
must also be BSI or ASTA approved.
The wires in this mains lead arecoloured as such:
GREEN & YELLOW - Earth
BROWN - Live
BLUE - Neutral
Please note that the colour of these mains wires
may not correspond with the colour markings
that identify the terminals in your plug.
