3
3. Secure the Mounting Bracket (L) to the wall.
4. Hangthe mainbodyontheMountingBracket.
Turning the unit on/off and setting the
Digital Thermostat (BPH1520 Only)
1. Plug unit into wall socket.
2. Locate on/off switch on the bottom of the
right end cap and switch to the on position.
3. Press ( ) Mode button (F):
• 1
st
= LO; runs continuously on Low.
• 2
nd
= HI; runs continuously on High.
• 3
rd
= Auto Low (AL); press (+) or (-)
to set desired temperature.
• 4
th
= Auto HI (AH); press (+) or (-)
to set desired temperature.
4. Once you have selected the mode and
temperature, the display returns to the
current room temperature and gradually
increases as the room warms.
5. If you selected anAuto mode and the
heater does not start, make sure the set
temperature is higher than the current
room temperature.
6. To turn the unit off keep pressing the mode
button (F) until all mode indicator lights (E)
are not illuminated.
7. Switch off the on/off switch located on the
bottom of the right end cap.
NOTE: The mode Indicator Light (E)
will flash in the AUTO mode if the set
temperature is lower than the current
room temperate displayed on the
Display, this is also the same if the
unit has reached the required set
temperature.
NOTE: In Auto mode, it is normal for
the heater to cycle ON and OFF as it
maintains the programmed temperature.
To prevent the unit from cycling, raise
the thermostat setting.
The Digital Thermostat remembers the
previous temperature setting after the
unit is turned off. However, if the unit
is unplugged, the digital thermostat
resets and no longer remembers the
previous temperature setting.
Turning the unit on/off and setting the
thermostat (BPH1414 Only)
1. Plugunit intowallsocket.
2. Rotatethemodeadjustmentknobclockwise
fromthe(0)positiontoeither1 (Lowsetting)or
2(Highsetting)togetaconstantheatoutput.
3. To find the ideal thermostat setting, turn
the thermostat adjustment knob clockwise
to “max”.
4. When the desired temperature is reached
slowlyturnthethermostatknob anti-clockwise
until the heater turns off.
5. The heater will now automatically retain
the temperature at the required level.
6. To turn the unit off rotate the mode
adjustment knob anti-clockwise to the
(0) position.
PROGRAMMABLE TIMER (BPH1520 Only)
You can program your heater to turn on at a
preset time or turn off after a set amount of time.
Setting the On Timer:
1. With the heater off, press and hold (+) and
(-) simultaneously until the display flashes
and display the number “0”.
2. Press (+) or(-)toselecttheamountof time you
would liketo pass beforetheheater turnson.
3. After setting the timer, the display shows
a red dot next to the current room
temperature on the display to indicate
that the timer is activated.
4. After the programmed length of time has
passed, the heater automatically turns on
Auto HI at 24°C (75°F) for 2 hours.
Setting the Off Timer:
1. Select the desired mode and/or temperature.
2. With theheaterrunning,pressandhold(+)
and (-)simultaneouslyuntilthedisplayflashes.
3. Press (+) or (-) to select the amount of time
you would like the heater to run.
4. After setting the timer, the display shows a
RED dotnext to currentroomtemperatureon
thedisplaytoindicatethatthetimerisactivated.
5. The heater automatically shuts off after the
programmed length of time has passed.
FROST GUARD (BPH1520)
Press the( ) Mode button 5 consecutive times
forAnti Frost setting (AF will show in the digital
display). This special setting is automatically
activated when the (AF) mode is selected. In this
mode,theheaterisoffuntiltheroom’s temperature
reachesfreezingandtheheaterautomaticallyturns
on HI power.The heater will cycle ON and OFF
as it maintains the temperature between 5-8 °C.
FROST GUARD (BPH1414)
Keepunit in 1 (lowsetting)or2(highsetting)
rotate thermostatadjustmentknobtobeginning
position( ).Unitwill stopworking.This special
settingisautomaticallyactivated.Inthismode,the
heater is offuntiltheroom’stemperaturereaches
freezingand theheaterautomaticallyturnsonHI
power.The heaterwill cycleONandOFFas it
maintains thetemperaturebetween5-8°C.
AUTO SAFETY SHUT OFF
The heater has a built in safety device which
will switch off the heater automatically in case
of accidental overheating. It can only resume
operation when the user has reset the unit. For the
BPH1520 (OH) will display in an overheat situation.
RETAIN THE FOLLOWING FOR
FUTURE REFERENCE.
DESCRIPTIONS (See Fig.1 & 2)
A. Left End Cap
B. Rear Housing
C. Right End Cap
D. Display
E. Mode Indicator Lights
F. Mode Button/Adjustment
G. ThermostatAdjustment
H. Base
I. Grill
J. Power light
K. Base Mount
L. Mounting Bracket (Figure 5)
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating,
do not cover the heater ( ).
3. DO NOT position the heater directly under a
power socket.
4. Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If thesupplycordorplugis damaged,itmust
bereplacedbythe manufactureroritsservice
agentorsimilarly qualifiedpersonin orderto
avoidhazard.Theheatercontainsnouser
serviceableparts.Shouldtheproductsuffer
damage or breakdown,itmustbereturnedto
the manufacturerortheirserviceagent.
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. Do not use this heater with a programmer,
timer or any other device that switches
the heater on automatically, since a fire
risk exists if the heater is covered or
positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10.DO NOT position where it can be touched by
children, especially the very young.
11. Allow a safe area around the heater away
from furniture or other objects; at least
50 cm from the top and sides and 200 cm
at the front.
12.Do not use this heater when it is lying on
its side.
13.DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when
gluing or varnishing parquet floors, PVC etc.)
14.DO NOT insert any objects into the heater.
15.Keep the mains cord at a safe distance from
the main body of the heater.
16.If overheating should occur, the built-in
overheating safety device will switch off
the heater.
17. Do not place the cord under a rug.
18.The heater is to be installed so that switches
and other controls cannot be touched by a
person in the bath.
19.Heater must be installed at least 0.6 m
above the floor.
20.The heater cannot be used adjacent to
curtains or combustible material. Curtains or
combustible material may be burned if the
heater was installed incorrectly.
21.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
22.WARNING: RiskofFire.Discontinueuseifthe
outlet or plug become hot to the touch.
Overheating may indicate awornor damaged
outlet. Consult a qualified electrician for
outlet replacement.
23.CAUTION: Inorder to avoid a hazard due
to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied
through an external switching device, such
as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
BASE ASSEMBLY (See Fig. 3)
1. Insert base (H) into the bottom of the base
mount (K) which is attached to the bottom of
the Grill (I).
WALL MOUNTING ASSEMBLY
(See Fig. 4 – Fig. 6)
IMPORTANT: Beforedrillinginto anywall
ensure no electrical cables are present in the
area.
NOTE: Due to the multitude of potential
mounting surfaces, mounting screws are not
included with this product. Please seek
professional assistance or visit your local
hardware store to determine which type of screw
is best for your particular wall.
1. Remove Base (H) from the bottom of the
Base Mount (K).
2. Remove Base Mountfrom thebottom of the
Grill(I) by removing the two securing screws.
ENGLISH
2
