Bedienungsanleitung Bischoff und Bischoff Centuro S7 (Seite 25 von 71) (Deutsch, Englisch, Französisch, Spanisch)

802030

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Bischoff & Bischoff GmbH |28.07.2020 - revision 3

4948

Centuro S7 | Scooter Scooter | Centuro S7

Moving the seat

• Pull the lever (on the right below the seat surface, Fig. 05) towards

you. The seat can now be moved forwards and backwards.

• You can now adjust the seat to the required position.

• Release the lever and ensure that the seat is locked in one of the

closest fixed positions.

Seat height

You will firstly need to remove the seat.

• Fold the back rest onto the seat by holding the back rest with your

right hand and using your left hand to lift up the lever on the

left next to the seat surface (Fig. 08). The back rest will then fold

forwards automatically.

• Simply remove the seat by pulling it upwards (Fig. 6).

• Undo the screw connection (Fig. 7) and position the seatpost in the

required position inside the tube guide.

• Then securely tighten the screw connection again (Fig. 7) using

40Nm in the next hole.

• Now place the seat back onto the mounting.

• Make sure that it is locked in position again.

3.5.4. Back rest

The angle of the back rest on your scooter can be adjusted forwards

and backwards. You also have the possibilty to limit the adjustment

range backwards

Adjusting the angle

• Pull the lever (on the left on the seat, Fig. 08) upwards. The back

now pushes forwards.

• Push the back rest into the required position.

• Release the lever and make sure that the back rest is locked in

position again.

• Please note that the adjustment of the seat to the rear and/or the

angle adjustment to the rear can increase the overall length of the

scooter.

3.5.5. Arm rest

The arm rests can be swivelled upwards in order to make it easier to

mount and dismount. In addition, the height, distance and angle of the

arm rests can be adjusted.

Height

• Loosen the screw until you can remove it, hold the screw in its

position. Now you can move the arm rest vertically up and down

(Fig. 9).

• Move the arm rest to its preferred height and tighten the screw.

Side distance

• Undo the hand screw (Fig. 10) on the back of the back rest frame

while holding onto the armrest.

• Adjust to the required distance and tighten the screw again.

• The armrests can also be removed (e.g. for replacement, storage or

transportation) after undoing the screw on the back of the frame

(Fig. 10).

• Please note that pulling the armrests out to the side can increase

the vehicle width.

Angle of support

• You can adjust the angle of support of the armrests by screwing

the knurled nut (Fig. 11) on the relevant armrest further in or by

unscrewing it.

3.5.6. Seat belt (optional)

The seat belt will be attached to the frame from the side.

• Adjust the belt length to meet your needs by positioning the clasp

accordingly.

• Fasten the belt with the belt buckle.

• Unfasten the belt by pressing the red button (Fig. 12) on the belt

buckle

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bischoff und Bischoff Centuro S7 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bischoff und Bischoff Centuro S7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info