Bedienungsanleitung Bissell 1867 (Seite 5 von 8) (Englisch)

560228

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1

Getting ready continued

3. Twist the quick release cord wrap to unwrap the power cord and plug into a 120-Volt

grounded outlet as described in the Important Safety Instructions, on page 2.

4. The ready light will illuminate when the Steam Mop is ready for use.

NOTE: During the first use it may take several seconds for the Steam Mop to begin

steaming. The water needs to flow through the filter to the heater. The delay will only

occur during initial use or when using a new filter.

Operation

Tip:

Do not attempt to use your Steam Mop without water

in the tank.

Cleaning hard floors

Your Steam Mop is designed to clean hard flooring such as ceramic tile, laminate, marble, stone and sealed

hard wood floors. Use of your Steam Mop on waxed or some unwaxed floors may result in diminished

glossiness. On surfaces that have been treated with wax, the wax may be removed by the heat and steam

action. Do not use on unsealed wood floors or let unit stand on any wood floor for an extended period of

time. This could cause the wood grain to rise. When using on peel-and-stick vinyl, linoleum or any other

heat sensitive floors, use extra caution. Too much heat can melt down glue in the flooring. For best results

test in an inconspicuous area and check the care instructions from your flooring manufacturer.

1. When the ready light illuminates, begin cleaning by passing over surface while pressing

trigger to emit steam.

2. To sanitize an area of your floor, place the center of the Steam Mop over the spot for a

minimum 15 seconds, but no longer than 20 seconds.

3. When the Steam Mop stops emitting steam, simply remove the water tank, refill, and continue

cleaning.

Carpet Refresher Attachment (select models only)

This accessory is recommended for the refreshing of

carpets. Once the steam mop is cradled in the carpet

refresher attachment, it will easily glide over the carpet.

NOTE: Always be sure a mop pad is in place

before placing in carpet refresher attachment. It is

recommended that only white mop pads be used with

the carpet attachment. Do not use carpet attachment

on spots or stains, or glide it over the same spot for

longer than 20 seconds.

1. Attach the mop pad to the swivel mop head. As

directed in step 1 on page 4.

2. Place the swivel mop head, with mop pad attached, in

the carpet refresher attachment.

Note: that the Steam Mop rests in the carpet refresher

attachment and may not stay attached to the swivel mop

head. It is meant to glide over the carpet.

3. Fill the water tank with water. Begin refreshing your

carpet or rug by pushing the Steam Mop in a forward

and backward motion, releasing steam as you go.

CAUTION:

Never put descaling,

alcoholic, or deter-

gent products into

the steam cleaner,

as this may damage

it or make it unsafe

for use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bissell 1867 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info