655053
4
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
6
DS909839-001 DS909839-001
7
In this mode, the switchboard intercepts all the calls coming from the door unit and rings with a dual-tone
sound; when a call arrives, the led “S” starts blinking red and stays on until the conversation end.
To answer the call, the attendant must pick the handset up and speak BY KEEPING the button
PRESSED. To
activate the electric lock, press the button “DOOR OPENER”.
After answering, to call a user it is necessary to enter the code associated to the desired user and press the
button
. The status led blinking red changes and becomes steady red for about two seconds and then
becomes yellow to indicate to the attendant that the call has been forwarded and the switchboard is waiting
for an answer; to connect the called user to the door unit, press one of the two “R” buttons. It is possible
to connect a user called by the switchboard only if the switchboard has received before a call from the door
unit.
At any time, except when a conversation is already in progress, any user can call the switchboard attendant by
pressing the “DOOR OPENER” button present on his door phone or video door phone.
Also the attendant can call any user at any time, simply by entering the associated code and then pressing
the button
.
If the attendant, after calling a user, while he is waiting for an answer (the status led is yellow), wants to
call another user, he must interrupt the fi rst call by hanging the handset up, in order to put the switchboard
back in standby mode. When the status led will light again in green, the attendant will be able to perform a
new call.
“Partial” mode.
The led “S” blinks in green.
In this mode, the switchboard allows all calls to pass and directly arrive to the called user, but, however, it
can call and be called by all the users.
S LED
The status led “S”, present on the switchboard cover, is a bicoloured led and provides the following
information:
off
Switchboard in NIGHT mode, deactivated.
green
Switchboard in standby, in TOTAL DAY mode.
green blinking
Switchboard in standby, in PARTIAL DAY mode.
red blinking
It signals the presence of a call coming from the door unit.
red
A communication in progress is going to be forwarded.
yellow
The communication has been forwarded to the desired user and the switchboard is
waiting for an answer.
COMMAND FOR RING VOLUME ADJUSTMENT
On the switchboard it is possible to adjust the ring level of calls coming from a door unit. The level can be
high, medium and low and can be adjusted with a switch accessible from the lower switchboard edge. It is not
possible to adjust the volume of calls coming from apartment stations.
AN9839/1 CONCIERGE SWITCHBOARD
The switchboard allows the following functions:
Audio conversation with door units
Door opening
Electronic call to users
Capability to adjust the ring level among high, medium and low
Capability to select operating mode between DAY/NIGHT
Capability to select the management mode between PARTIAL/TOTAL
Two signalling leds available for auxiliary information (for ex. Open door)
Button for audio
enabling with door unit
Call forwarding buttons
Door opener button
Bicoloured STATUS led
TOTAL/PARTIAL button
Apartment station call button
Switch for call volume adjusting
Green led available from outside
Red led available from outside
Day/Night button
Fig. 2
USE
The switchboard has two different operating states, that can be selected by the attendant:
NIGHT MODE
The status LED (Fig. 2) is off.
In this mode, the switchboard is disabled and the system operates as if the switchboard was not present,
allowing visitors to directly call users, that of course can answer and open the door lock.
In this operating mode, users can not call or be called by the switchboard.
In case of mains fail, the switchboard will operate as if it was in “night” mode. After mains return, the
switchboard will continue to operate in “night” mode, regardless of the state it was before the power-
off.
By pressing the button
, the switchboard is enabled to operate in “DAY” mode.
DAY MODE
In this mode the switchboard is active and can operate in two different ways, called “TOTAL” and “PARTIAL”.
The button “P/T” allows to select the operating mode between Total and Partial.
At power-on, it is automatically set in TOTAL mode; by pressing the button, the switchboard operating mode
will change in PARTIAL mode.
The operating mode is signalled by the status led “S”, that lights steady or blinking.
“Total” mode.
The status led “S” lights green.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

bitron-video-an9839---lbt90264

Suche zurücksetzen

  • ich habe eine Bitron Gegensprechanlage mit 2 Klingelknöpfen am Gartentor. Leider ist die Anlage aufgeschraubt und ich kenne nicht die Modelnummer.Kann man so etwas wieder reparieren oder austauschen. Es sind etwa 8 Drähte die zum Haus führen . Im Haus gibt es 2 Telefonhörer die zur Zeit nur ein Summen mit Schwingungen machen.
    Eingereicht am 26-4-2020 14:10

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bitron Video AN9839 - LBT90264 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info