Bedienungsanleitung Black Decker ASI200 T1 (Seite 5 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581276

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH

X When the item to be inflated has reached the preset

value the unit will automatically turn off.

X To turn the inflator off press switch (5) to the 0 position.

X Remove the valve adaptor or accessory from the

inflated item and the 12 Volt adapter (6) from your

vehicle's 12 Volt accessory socket.

Note: If the 12 Volt adapter is removed from the vehicles

12 Volt accessory socket, all settings will be lost and will

need to be re-entered following the instructions under the

heading 'Setting the required pressure'.

Operating the area light

X To operate the area light (1), make sure that the 12 Volt

adaptor (6) is plugged into the vehicle's 12 Volt

accessory socket.

Note: Make sure that your 12 Volt accessory socket is live.

On some vehicles the accessory socket may only become

live when the ignition key is in the accessory position.

X To turn the area light on, press the area light on/off

switch (7) located on the side of the unit to the I position.

X To turn the area light off, press the area light on/off

switch (7) located on the side of the unit to the 0

position.

To replace the bulb (fig. E)

Warning! Make sure that the 12 Volt adaptor is not

connected before starting this procedure.

X Remove the screw (10) from the top of the lens

cover (12).

X Pull the lens cover (12) down using the tab (11) to get

access to the bulb (13).

X To remove the bulb, push in and turn clockwise (fig. E).

X Replace the bulb (13) with a one of the same type and

wattage (12V/5W).

X Fit the lens cover (12) and secure with the screw (10).

Using your inflator as a pressure gauge

X Make sure that the unit is powered as described in the

section 'Operating the Inflator'.

X Connect the universal valve adaptor and accessories if

required to the item to be inflated making sure that the

lever of the valve adaptor is in the down position to lock

it in place.

X The display will now show the actual pressure value in

the item.

Maintenance

Your Black & Decker corded/cordless appliance/tool has

been designed to operate over a long period of time with

a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular

cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

X Switch off and unplug the appliance/tool.

X Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

X Or run the battery down completely if it is integral and

then switch off.

X Unplug the charger before cleaning it. Your charger

does not require any maintenance apart from regular

cleaning.

Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Regularly open the chuck and tap it to remove any dust from

the interior (when fitted).

Troubleshooting

Replacing the fuse in the vehicle dc accessory plug

X Remove the cap by turning it counter-clockwise.

X Loosen the cap and centre pin.

X Remove the fuse.

X Fit a new fuse of the same type and size (8A/250V).

X Refit the cap and centre pin.

X Tighten the cap by turning clockwise onto the plug.

Problem Possible cause Possible solution

Inflator will not

operate

12 Volt adaptor

not connected

Connect the 12 Volt

adaptor

Accessory socket

not live

Turn key to accessory

position

No preset

valve set

Set preset value

The fuse in the

12 Volt adaptor

is blown

Replace the fuse with

one of the same size

and type (8A/250V)

Cord or switch is

damaged.

Have the cord or

switch replaced at a

Black & Decker Service

Centre or Authorized

Service Centre.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ASI200 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker ASI200 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info