Bedienungsanleitung Black Decker ASI500 TH2 (Seite 7 von 94) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581290

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

ENGLISH

Before use (fig. A)

The internal battery must be recharged for 4 to 5 hours using

the AC charger (13) provided.

 Insert the jack plug (9) into the jack plug socket (11) on

the front of the unit.

 Plug the AC charger (13) into the mains power supply.

 The LED (15) on the AC charger (13) will indicate the

level of charging. Red, unit charging, Green, unit

charged.

 When fully charged, remove the AC charger from the

mains and remove the jack plug from the unit.

Note: Store your AC charger in a safe place for later use.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These include:

 Injuries caused by touching any rotating/moving parts.

 Injuries caused when changing any parts, blades or

accessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods make sure you take

regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF).

Use

Hose and cord storage (fig. B - D)

 Wrap the 12 Vdc cord (17) around the base of the unit

and locate the 12 Vdc adapter (8) into its storage

location (16) as shown in fig. B and then rotate through

90° to secure in place.

 The air hose (5) is located in a storage channel (26)

around the top of the unit (fig. C), make sure the hose is

snapped into the retaining clips and the lever (19) is in

the up position (fig. D).

 The high-volume hose (7) is stored in a storage channel

around the centre of the unit and snaps into position at

both ends. The accessories (14) are stored on the front

of the unit.

Fitting the accessories (fig. D, G - I)

Your inflator is supplied with the standard tapered nozzles

and the needle inflator nozzle, these are stored on the front

of the unit (14).

 To use the universal valve adaptor (6), make sure that

the lever (19) is in the up position.

 Place the universal valve adapter (6) over the stem of

the inflation needle or tapered nozzle (fig.D).

 Press the lever (19) on the universal valve adapter (6)

down to lock it in place.

 Place the inflation needle or tapered nozzle into the item

to be inflated.

Note: Always make sure that the lever is in the up position

when not in use. Operate your inflator only with the universal

valve adaptor or with the included nozzles.

Note: Make sure that the universal valve adapter is firmly

locked in place before turning the inflator on.

Your inflator is supplied with a high volume adaptor (24).

This is stored on the front of the unit (fig. G).

 To use the high volume adaptor (24), remove it from the

high volume inflate connection (10).

 Remove the high volume hose (7) from the storage

location.

 Remove the tapered nozzle (18) from the end of the

high volume hose (7).

 Fit the high volume adaptor (24) to the end of the high

volume hose (fig. H).

Many inflatables have an internal flap that prevents air loss

during inflation, especially air mattresses. Unless this flap is

displaced by the nozzle the inflatable will not inflate. Push

the nozzle firmly into the valve to make sure that you push

this flap out of the way.

Warning! Excessive air pressure may cause a hazardous

risk of bursting or personal injury. Check the manufacturer's

maximum pressure rating for items being inflated.

Note: If the pressure rating for the item being inflated

is above 100 PSI / 6.89 BAR / 689 KPA, note that the

maximum run time is 10 minutes, leave to rest for 20 minutes

before re-use.

Operating the inflator (fig. E)

Warning! Do not operate the inflator when the car engine

is running.

Note: Make sure that your 12 Vdc accessory socket is live.

On some vehicles the accessory socket may only become

live when the ignition key is in the accessory position.

To power the display from the 12 Vdc adapter:

 Always fully extend the 12 Vdc cord before each use.

 Connect the 12 Vdc adapter (8) into your vehicles

12 Vdc accessory socket.

 Switch the main power switch (1) to the inflate

position (c) to power-up the LCD.

To power the LCD from the internal battery (cordless

operation):

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ASI500 TH2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker ASI500 TH2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info