Bedienungsanleitung Black Decker ast 4 (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389542

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for sanders

◆ Always wear a dust mask whenever sanding.

◆ Thoroughly remove all dust after sanding.

◆ Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal

which may produce toxic dust:

- Wear a dust mask specifically designed for protection

against lead paint dust and fumes and ensure that

persons within or entering the work area are also

protected.

- Do not let children or pregnant women enter the work

area.

- Do not eat, drink or smoke in the work area.

- Dispose of dust particles and any other debris safely.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Features

1. On/off switch

2. Dust extraction outlet

3. Sanding base

4. Paper clamp lever

5. Variable speed control knob (KA196E)

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting sanding sheets (fig. A & B)

Warning! Never use the tool without a sanding sheet or

accessory in place.

Fitting regular sanding sheets (fig. A)

◆ Make sure that the tool is switched off and unplugged.

◆ Soften the sanding sheet by rubbing its non-abrasive side

over the edge of a worktop.

◆ Press the paper clamp levers (4) upwards to release them

from the retaining grooves and open the paper clamps by

pressing them down.

◆ Place the sheet onto the sanding base, making sure that

the holes in the sheet line up with the holes in the base.

◆ Insert the edge of the sanding sheet into the front paper

clamp as shown.

◆ Press the front paper clamp lever (4) downwards and

locate it in the retaining groove.

◆ While keeping a slight tension on the sheet, insert the

rear edge of the sheet into the rear paper clamp.

◆ Press the rear paper clamp lever (4) downwards and

locate it in the retaining groove.

KA196/KA196E - Fitting sanding sheets with nylon loops

(fig. B)

◆ Make sure that the tool is switched off and unplugged.

◆ Press the sheet firmly and evenly onto the sanding base

(3), making sure that the holes in the sheet line up with

the holes in the base.

Connecting a vacuum cleaner (fig. C)

◆ Insert the adaptor (6) into the dust extraction outlet (2).

◆ Connect the hose (7) of the vacuum cleaner to the

adaptor.

Use

Warning! Let the tool work at its own pace. Do not overload.

KA196E - Variable speed control

The variable speed control allows you to adapt the speed of

the tool to the workpiece material.

◆ Set the control knob (5) to the desired setting. Use a high

speed for wood, medium speed for veneer and synthetics

and low speed for acrylic glass, non-ferrous metals and

for removing paints.

Switching on and off

CD380/CD400/AST4XC

◆ To switch the tool on, slide the on/off switch (1) forward

(position I).

◆ To switch the tool off, slide the on/off switch to the rear

(position 0).

AST4XC_EURA5.P7 16-08-2005, 20:254

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ast 4 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info