Bedienungsanleitung Black Decker AST18XC (Seite 4 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

53556

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Warning! Never change the direction of rotation while

the motor is running.

Selecting the drilling mode

• For drilling in masonry, set the drilling mode selector

(4) to the position.

• For drilling in other materials and for screwdriving,

set the drilling mode selector (4) to the

position.

Switching on and off (ﬁg. E)

• To switch the tool on, press the variable speed switch

(1). The tool speed depends on how far you press

the switch. As a general rule, use low speeds for

large diameter drill bits and high speeds for smaller

diameter drill bits.

• For continuous operation, press the lock-on button

(2) and release the variable speed switch. This

option is available only at full speed.

• To switch the tool off, release the variable speed

switch. To switch the tool off when in continuous

operation, press the variable speed switch once

more and release it.

Accessories

The performance of your tool depends on the accessory

used. Black & Decker and Piranha accessories are

engineered to high quality standards and designed to

enhance the performance of your tool.

By using these accessories you will get the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care

and regular cleaning.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be ﬁtted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

new plug.

• Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth

terminal. Follow the ﬁtting instructions supplied with good

quality plugs. Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you ﬁnd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product

available for separate collection.

Additional safety instructions for hammer drills

• Wear ear protectors. Exposure to noise can cause

hearing loss.

• Use auxiliary handles supplied with the tool. Loss

of control can cause personal injury.

• Preferably wear a dust mask.

Electrical safety

This tool is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on

the rating plate.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Side handle

6. Chuck

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (ﬁg. A)

• Turn the grip (7) counterclockwise until you can

slide the side handle (5) onto the front of the tool as

shown.

• Rotate the side handle into the desired position.

• Tighten the side handle by turning the grip

clockwise.

Fitting a drill bit or screwdriver bit (ﬁg. B)

• Open the chuck by turning the front part (8) with one

hand while holding the rear part (9) with the other.

• Insert the bit shaft (10) into the chuck and ﬁrmly

tighten the chuck.

Removing and reﬁtting the chuck (ﬁg. C)

• Open the chuck as far as possible.

• Remove the chuck retaining screw (11), located in

the front part of the chuck, by turning it clockwise

using a screwdriver.

• Tighten an Allen key (12) into the chuck and strike

it with a hammer as shown.

• Remove the Allen key.

• Remove the chuck by turning it counterclockwise.

• To reﬁt the chuck, screw it onto the spindle and

secure it with the chuck retaining screw.

Use

Warning! Before drilling into walls, ﬂoors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation (ﬁg. D)

• For drilling and for tightening screws, place the

forward/ reverse switch (3) in the neutral position.

• For loosening screws or removing a jammed drill bit,

turn the forward/reverse switch (3) to the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker AST18XC Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info