Bedienungsanleitung Black Decker AST8XC (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

53571

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Saw blade storage (KS702PE & KS703PE) (fig. E)

Saw blades (8) can be stored in the storage compartment (7)

located on the side of the tool.

X Open the cover of the saw blade storage compartment (7)

by holding the tab on the top of the door and pulling

outwards.

X Remove or store the saw blades (8) in the saw blade

storage compartment. (7).

X Close the cover of the saw blade storage compartment (7)

and make sure that it is latched closed.

Cut line blower (fig. F)

X To aid visibility when cutting, your jigsaw is equipped with

a cut line blower (14) which will keep the work area clear of

dust as you saw.

Use

Adjusting the shoe plate for bevel cuts (fig. G)

The shoe plate (4) can be set to make either a straight cut or

a left or right bevel cut at an angle of 45°.

X Loosen the two screws (9).

X Pull the shoe plate (4) forward, rotate the shoe plate (4) to

the left or right and push it back into the 45° location.

X Push the saw blade support roller (5) forward until it

touches the saw blade (8).

X Tighten the two screws (9).

To reset the shoe plate for straight cuts:

X Loosen the two screws (9).

X Pull the shoe plate (4) forward, rotate to the centre and

push it back into the 0° location.

X Push the saw blade support roller (5) forward until it

touches the saw blade (8).

X Tighten the two screws (9).

Setting the pendulum stroke (fig. H)

X Set the pendulum stroke selector (6) to the required

position.

X Position 0: metal and aluminium and sheet metal.

X Position I: for laminates, hard wood, work tops.

X Position II: for plywood and PVC/Plastics.

X Position III: for soft wood and fast cutting.

Variable speed control

The tool has a variable speed On/Off switch (1). The

operating speed depends on how far you press the switch.

Use a high speed for wood, medium speed for aluminium and

PVC and low speed for metals other than aluminium.

Switching on and off

X To switch the tool on, press the on/off switch (1).

X To switch the tool off, release the on/off switch (1).

X For continuous operation, press the lock-on button (2) and

release the on/off switch (1).

X To switch the tool off when in continuous operation, press

and release the on/off switch (1).

Sawing

Hold the tool firmly with both hands while cutting.

The shoe should be held firmly against the material being

cut. This will help prevent the saw from jumping, reduce

vibration and minimise blade breakage.

X Let the blade run freely for a few seconds before starting

the cut.

X Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Sawing laminates

When cutting laminates splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate

is sitting on the presentation surface either use a saw blade

that cuts on the downward stroke or:

X Use a fine-tooth saw blade.

X Saw from the back surface of the workpiece.

X Clamp a piece of scrap wood or hardboard to both sides of

the workpiece to minimise splintering, and saw through

this sandwich.

Sawing metal

X Be aware that sawing metal takes much more time than

sawing wood.

X Use a saw blade suitable for sawing metal.

X When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

X Spread a film of oil along the intended line of cut.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper care

and regular cleaning.

Warning! Before performing any maintenance or cleaning,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

X Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

X Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid get inside the tool and never immerse any part of

the tool into liquid

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker AST8XC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker AST8XC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info