Bedienungsanleitung Black Decker BCBL200 L25 (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709444

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

Charging a battery (BCBL200 L and BCBL200 L25

units only) (g. A)

BLACK+DECKER chargers are designed to charge

BLACK+DECKER battery packs.

u Plug the charger (4) into an appropriate outlet before

inserting a battery pack (3).

u Insert the battery pack (3) into the charger, making sure

the battery pack is fully seated in the battery slots

(Figure A).

The LED (4a) will ash indicating that the battery is being

charged.

The completion of charge is indicated by the LED remaining

on continuously. The pack is fully charged and may be used at

this time or left in the charger.

u Recharge discharged batteries as soon as possible after

use or battery life may be greatly diminished.

For longest battery life, do not discharge batteries fully.

It is recommended that the batteries be recharged after

each use.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged battery. The LED

ashes in the pattern indicated on the label. If you see this bad

battery blink pattern, do not continue to charge the battery.

Return it to a service center or a collection site for ecycling.

Hot/cold pack delay

When the charger detects a battery that is excessively hot or

excessively cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life.

The light ashes in the pattern indicated on the label.

Leaving the battery in the charger

The charger and battery pack can be left connected with

the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged.

This charger features an automatic tune-up mode which

equals or balances the individual cells in the battery pack to

allow it to function at peak capacity.

Battery packs should be tuned up weekly or whenever the bat-

tery no longer delivers the same amount of work. To use the

automatic tune-up mode, place the battery pack in the charger

and leave it for at least 8 hours.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 18 ° – 24 °C. DO NOT charge the battery pack in

an air temperature below +4.5 °C), or above +40 °C. This

is important and will prevent serious damage to the battery

pack.

u The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem.

To facilitate the cooling of the battery pack after use, avoid

placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

u If the battery pack does not charge properly:

u Check operation of receptacle by plugging in a lamp

or other appliance;

u Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

u Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 18 ° – 24 °C;

u If charging problems persist, take the tool, battery

pack and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily

done previously. DO NOT CONTINUE to use under

these conditions. Follow the charging procedure. You

may also charge a partially used pack whenever you

desire with no adverse effect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Unplug the

charger before attempting to clean.

u Do not freeze or immerse the charger in water or any

other liquid.

To install battery pack (BCBL200 L and

BCBL200 L25 units only) (g. B)

u Insert battery pack (3) into tool until an audible click is

heard as shown in Figure B. Make sure battery pack is

fully seated and fully latched into position.

To remove battery pack (g. C)

u Depress the battery release button (3a) in the battery

pack (3) and pull battery pack out of tool assembly (5) as

shown in Figure C.

To t the blower tube (g. D)

u Attach the blower tube (2) to the blower main body by

placing the tabs (2b) into the recesses (2a). To remove the

blower tube, depress the tabs (2a) and pull apart.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BCBL200 L25 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info