Bedienungsanleitung Black Decker BD1800JS T1 (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

580860

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Additional safety instructions for batteries and

chargers

Batteries

 Never attempt to open for any reason.

 Do not expose the battery to water.

 Do not store in locations where the temperature may

exceed 40 °C.

 Charge only at ambient temperatures between 10 °C and

40 °C.

 Charge only using the charger provided with the tool.

 When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

Do not attempt to charge damaged batteries.

Chargers

 Use your Black & Decker charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

 Never attempt to charge non-rechargeable batteries.

 Have defective cords replaced immediately.

 Do not expose the charger to water.

 Do not open the charger.

 Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

The charger automatically shuts off if the ambient

temperature becomes too high. As soon as the

ambient temperature has cooled down, the charger

will resume operating.

Charge only at ambient temperatures between

10 °C and 40 °C.

Charging process completed

Charging

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-off button

3. Turbo selector

4. Saw blade locking lever

5. Saw blade support roller

6. Saw blade

7. Shoe plate

8. Shoe plate locking knob

9. Saw blade storage compartment

10. Dust extraction adaptor

11. Battery

Fig. A

12. Charger

13. Charger receptacle

14. Charging indicator

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing the battery (ﬁg. B)

 To ﬁt the battery (11), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

 To remove the battery, push the release button (15) while

at the same time pulling the battery out of the receptacle.

Fitting the battery cap (ﬁg. C)

Warning! Fit the cap (16) to the battery (11) for transportation

and storage.

Fitting the saw blade (ﬁg. D)

 Hold the saw blade (6) as shown, with the teeth facing

forward.

 Push the lever (4) downwards.

 Insert the shank of the saw blade into the blade holder

(17) as far as it will go.

 Release the lever.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BD1800JS T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BD1800JS T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info