Bedienungsanleitung Black Decker BDCD8 (Seite 6 von 84) (Alle Sprachen)

661437

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

Warning! re Hazard. When disconnecting the charger from

the tool, be sure to unplug the charger from the outlet rst,

then disconnect the charger cord from the tool.

Trigger switch & reversing button (g. B)

u The drill is turned ON and OFF by pulling and releasing

the trigger switch (1)

u A forward/reverse control button (2) determines the direc-

tion of the tool and also serves as a lock off button.

u To select forward rotation, release the trigger switch and

depress the forward/reverse control button to the left.

u To select reverse, depress the forward/ reverse control

button the opposite direction.

u To lock the tool, set the forward/reverse slider into the

centre position.

Note! The center position of the control button locks the tool

in the off position. When changing the position of the control

button, be sure the trigger is released.

Keyless chuck (g. C)

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before installing or removing acces-

sories.

To insert a drill bit or other accessory:

u Grasp the rear half of the chuck (7) with one hand and use

your other hand to rotate the front half (8) in the counter-

clockwise direction, as viewed from the chuck end.

u Insert the bit or other accessory fully into the chuck, and

tighten securely by holding the rear half of the chuck and

rotating the front portion in the clockwise direction as

viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the drill

bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Use spade bits when drilling large diameter holes in wood.

u Use HSS drill bits when drilling in metal.

u Use masonry bits when drilling in soft masonry.

u Use a lubricant when drilling metals other than cast iron

and brass.

u Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw

Troubleshooting

Problem Possible cause Possible solution

Unit will not start. Battery pack not

charged.

Check battery pack charg-

ing requirements

Battery pack will not

charge.

Charger not plugged

in.

Surrounding air

temperature too hot or

too cold.

Plug charger into a work-

ing outlet.

Move charger and battery

pack to a surrounding air

temperature of above 40

degrees F (45ºC) or below

105 degrees F (+40.5ºC)

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCD8 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info