Bedienungsanleitung Black Decker BDCDD12 (Seite 6 von 92) (Alle Sprachen)

661440

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

(Original instructions)

Installing and removing the battery pack from the

tool (g. B)

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack:

u Insert battery pack into tool, until an audible click is heard

(g. B)

Removing the battery pack from the tool (g. C)

u Depress the battery release button as shown in (g. C)

and pull battery pack out of tool.

Operating Instructions

Trigger switch & reversing button (g. D)

u The drill is turned ON and OFF by pulling and releasing

the trigger switch (1). The farther the trigger is depressed,

the higher the speed of the drill operates at

u A forward/reverse control button (2) determines the direc-

tion of the tool and also serves as a lock off button.

u To select forward rotation, release the trigger switch and

depress the forward/reverse control button to the left.

u To select reverse, depress the forward/ reverse control

button the opposite direction.

u To lock the tool, set the forward/reverse slider into the

centre position.

Note! The center position of the control button locks the tool

in the off position. When changing the position of the control

button, be sure the trigger is released.

Torque control (g. E)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials require

a higher torque setting than small screws and soft workpiece

materials.

u For drilling, set the collar to the drilling position symbol

bu For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

u Set the collar to the lowest torque setting.

u Tighten the first screw.

u If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws

Keyless chuck (g. F)

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before installing or removing acces-

sories.

To insert a drill bit or other accessory:

u Grasp the rear half of the chuck (10) with one hand and

use your other hand to rotate the front half (11) in the

counterclockwise direction, as viewed from the chuck end.

u Insert the bit or other accessory fully into the chuck, and

tighten securely by holding the rear half of the chuck and

rotating the front portion in the clockwise direction as

viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the drill

bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Use spade bits when drilling large diameter holes in wood.

u Use HSS drill bits when drilling in metal.

u Use masonry bits when drilling in soft masonry.

u Use a lubricant when drilling metals other than cast iron

and brass.

u Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw

Troubleshooting

Problem Possible cause Possible solution

Unit will not start. Battery pack not

charged.

Check battery pack charg-

ing requirements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCDD12 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info