Bedienungsanleitung Black Decker BDCDD18 (Seite 7 von 108) (Alle Sprachen)

661441

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not

overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that

were easily done before. The battery may become warm

while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient tem-

peratures below 10 °C or above 40 °C. Recommended

charging temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above

40 °C.

The battery should be left in the charger and the

charger will begin to charge automatically when the

cell temperature warms up or cools down.

u To charge the battery (5), insert it into the charger (7).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (8) will blink.

The charge is complete when the charging indicator (8)

switches to continuously on. The charger and the battery

can be left connected indenitely. The LED will switch on

as the charger occasionally tops up the battery charge.

u Charge discharged batteries within 1 week. Battery

life will be greatly diminished if stored in a discharged

state.

Leaving the battery in the charger

The charger and battery pack can be left connected with

the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged.

Selecting the direction of rotation (g. D)

For drilling and for tightening screws, use forward

(clockwise) rotation. For loosening screws or removing a

jammed drill bit, use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse

slider (2) to the left.

u To select reverse rotation, push the forward/reverse

slider to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque

This tool is tted with a collar to set the torque for various

screwdriving and drilling applications. Large screws and

hard workpiece materials require a higher torque setting

than small screws and soft workpiece materials. For the

denition of the symbol refer to the listing below.

u For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the

symbol.

u For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed

as follows:

u Set the torque adjustment collar (4) to the lowest

torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the

correct setting. Use this setting for the remaining

screws.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the switch (1). The tool

speed depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the

drill bit.

u Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCDD18 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info