Bedienungsanleitung Black Decker BDCDS18 (Seite 7 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709549

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

Item Description

120 grit detailed nger sanding sheet.

For a medium nish for detailed sanding.

(Part Number - X3277-XJ)

Charging procedure (Fig. A)

BLACK+DECKER chargers are designed to charge

BLACK+DECKER battery packs.

u Plug the charger (6) into an appropriate outlet before

inserting the battery pack (5).

u Insert the battery pack (5) into the charger (6) as shown in

gure A.

u The LED (6a) will ash indicating that the battery is being

charged.

u The completion of charge is indicated by the LED (6a)

remaining on continuously. The pack is fully charged and

may be used at this time or left on the charger.

Note: Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished. For longest

battery life, do not discharge batteries fully.

It is recommended that the batteries be recharged after each

use.

Leaving the battery in the charger

The charger (6) and battery pack (5) can be left connected

with the LED glowing indenitely.

The charger will keep the battery pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a

service center for recycling.

Charger Diagnostics (Fig.B)

Refer to the indicators in gure B for the charge status of the

battery pack.

Bad Battery

If you see a bad battery blink pattern, do not continue

to charge this battery. Return it to a service center or a

collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life. A cold battery pack will charge at a

slower rate than a warm battery pack. The pack will charge at

that slower rate throughout the entire charging cycle and will

not return to maximum charge rate even if the pack warms.

Installing and removing the battery pack from the

tool

To install battery pack (Fig. C)

u Insert battery (5) into tool foot until an audible click is

heard (Figure. C)

u Ensure battery pack is fully seated and fully latched into

position.

To remove battery pack (Fig.D)

u Depress the battery release button (5a) as shown in gure

D and pull battery pack (5) out of tool foot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCDS18 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info