Bedienungsanleitung Black Decker BDCIM18 (Seite 8 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709458

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

(Original instructions)

u To lock the tool, set the forward/reverse slider (2) into

the centre position.

When changing the position of the forward/reverse slider

(2), make sure the variable speed switch (1) is released.

Note: The rst time the tool is run after changing the direc-

tion of rotation, you may hear a click on startu up. This is

normal and does not indicate a problem with the tool.

Note: The impacting noise that the tool makes is normal

and does not indicate a problem with the tool.

LED Work light (g. E)

u The LED work light (5) is located above the variable

speed switch (1).

u The LED work light (5) will be activated when the vari-

able speed switch (1) is pressed.

Note: The LED work light is for lighting the immediated

work surface and is not intended to be used as a torch.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the variable speed switch

(1). The tool speed depends on how far you press the

variable speed switch (1).

u To switch the tool off, release the variable speed

switch (1).

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the

drill bit.

u Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Use spade bits when drilling large diameter holes in

wood.

u Use HSS drill bits when drilling in metal.

u Use masonry bits when drilling in soft masonry.

u Use a lubricant when drilling metals other than cast

iron and brass.

u Make an indentation using a centre punch at the

centre of the hole to be drilled in order to improve

accuracy.

Screwdriving

u Always use the correct type and size of screwdriver

bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight

line with the screw

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

tool care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the

tool, remove the battery from the tool. Unplug the charger

before cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any

dust from the interior.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your BLACK+DECKER

product needs replacement, or if it is of no further use to

you, do not dispose of it with household waste. Make this

product available for separate collection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCIM18 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info