Bedienungsanleitung Black Decker BDS300 (Seite 4 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

473018

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

- Walls covered with metal

- Very humid conditions

- Shielded cables

◆ Before use, always test the tool by detecting a known

pipe or wire.

◆ If in doubt contact a qualified contractor.

Warning! This tool will not detect wires in circuits isolated

from the mains supply, cables operating at direct current (DC)

or wires used for telecommunication or computer systems.

Hidden wires (e.g. wall lights) may not be detected when

switches are in the off position.

Warning! This tool will not detect pipes of any other material

than metal.

Features

1. On/off switch

2. Mode selector switch

3. LED indicators (stud/metal finder)

4. LED indicator (AC wire)

Assembly

Fitting the battery (fig. A)

◆ Depress the release button (5) and slide the battery cover

(6) off the tool.

◆ Connect the battery to the connector. The larger battery

terminal connects to the smaller connector terminal.

◆ Refit the cover and let it click into place.

Use

Selecting the operating mode

◆ Set the mode selector switch (2) to the ‘STUD’ position for

the detection of wooden studs.

◆ Set the mode selector switch (2) to the ‘METAL’ position

for the detection of metal studs, pipes, etc.

Using the stud finder function (fig. B)

You can use this function to find wooden and metal studs

through drywall boards up to 18 mm thick.

◆ Set the mode selector switch (2) to the required position.

◆ Place the tool flat against the wall as shown.

◆ Keep the on/off switch (1) depressed.

The red LED indicator (3) will light up and the buzzer will

sound once while the tool is calibrating. After calibration is

completed:

◆ Slowly slide the tool in a horizontal direction. Make sure

not to tilt or lift the tool.

◆ When the red LED indicator (3) lights up, slow down and

slide the tool further until the buzzer sounds and the top

green LED indicator is on.

This position indicates the one edge of the stud.

◆ Mark this position using the centre of the tool as a

reference point.

◆ Move the unit further until the LED indicators are off.

◆ While still keeping the on/off switch (1) depressed,

move the tool in the opposite direction.

◆ When the red LED indicator (3) lights up, slow down and

slide the tool further until the buzzer sounds and the top

green LED indicator is on.

This position indicates the other edge of the stud.

◆ Mark this position using the centre of the tool as a

reference point.

The centre of the stud is between the two marks.

Using the metal finder function (fig. B)

You can use this function to find metal pipes through drywall

boards up to 18 mm thick.

◆ Set the mode selector switch (2) to the ‘METAL’ position.

◆ Place the tool flat against the wall as shown.

◆ Keep the on/off switch (1) depressed.

The red LED indicator (3) will light up and the buzzer will sound

once while the tool is calibrating. After calibration is completed:

◆ While holding the unit with one hand place your other

hand on the surface close to the area being scanned.

◆ Move the tool slowly and smoothly across the surface,

approaching from different directions.

◆ When the red LED indicator (3) lights up, slow down and

slide the tool further until the buzzer sounds and the top

green LED indicator is on.

This position indicates the location of a metal object.

◆ After detecting the work area repeat the testing

procedure to confirm the operation of the unit.

Using the wire detector function (fig. B)

You can use this function to find live wires through drywall

boards up to 38 mm thick. The function works continuously in

all modes.

Warning! Test the unit on a known AC current before use.

◆ Make sure the unit is away from the area being scanned

and any other AC current source. Static charge may

interfere detection on both sides of the wire, resulting in

limited accuracy.

◆ Keep the on/off switch (1) depressed.

The red LED indicator (4) will light up and the buzzer will sound

once while the tool is calibrating. After calibration is completed:

◆ While holding the unit with one hand place your other

hand on the surface close to the area being scanned.

◆ Move the tool slowly and smoothly across the surface,

approaching from different directions.

When an AC source is located, the red LED indicator (4) will blink.

◆ After detecting the work area repeat the testing

procedure to confirm the operation of the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDS300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info