581353
8
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
8
Part 1 (no load)
X Make sure that there is no load on the alternator by
turning off all the vehicles accessories.
X The battery must be fully charged before testing the
alternator.
X Run the engine for 3 minutes to achieve normal idle
speed and verify that there is a no-load voltage.
X Using the function control knob (3), select alternator
check (fig. C) before connecting the clamps to the
battery, ANALYSING ALTERNATOR will be displayed
after the clamps are connected.
X When the unit has completed checking, ALTERNATOR
GOOD will be displayed and the green LED will light to
indicate that the alternator is good or ALTERNATOR
BAD or ENGINE NOT RUNNING and the red LED will
light to indicate that the alternator is out of typical
voltage range.
Part 2 (under load)
X Load the alternator by turning on as many accessories
as possible except for air-conditioning and defrost.
X Once the unit has completed checking, ALTERNATOR
GOOD will be displayed and the green LED will light to
indicate that the alternator is good or ALTERNATOR
BAD or ENGINE NOT RUNNING and the red LED will
light to indicate that the alternator is out of typical
voltage range.
If the first alternator check indicates a good alternator and
the second indicates the alternator is not good, the problem
could be caused by any of the following:
X Loose fan belts.
X An intermittent diode failure.
X Bad connections between the battery and alternator
and/or ground.
Note: ALTERNATOR BAD or ENGINE NOT RUNNING may
be displayed if a number of extra accessory loads have been
added to the charging system, thereby increasing current
demand from the alternator. Make sure that the alternator is
rated to support the application.
Engine start (fig. C)
Using the function control knob (3) select engine start before
connecting the clamps to the battery.
X The LCD will show a 90-second count down, then
READY TO JUMP START ENGINE will display.
X Crank the engine using the manufacturers guidelines,
typically in 3 to 5 second bursts. The LCD displays
STARTING.
X Disconnect the mains cord and clamps observing the
“Safety instructions” at the front of this manual.
Warning! When a second attempt at starting an engine is
required, a five minute cooling down period is necessary
before attempting to re-start the engine.
The high current engine start function requires a resting/
cooling period between tries. The charger will not allow
operation in the engine start mode for 5 minutes. The LCD
will display COOLING DOWN, WAIT 5 MINUTES during this
time. After 5 minutes, repeat the above procedure.
Troubleshooting
Display indications, common problems and possible
solutions:
No Functions
X Make sure that the battery charger is plugged into a live
230 Vac outlet.
X Follow the steps outlined in the “Connecting the battery
charger” at the front of this manual.
X The unit will turn on automatically after being properly
connected to the battery. If it does not come on, either it
is not connected properly to the terminals or the voltage
of the battery to be serviced is too low (below 0.5 Volts).
Smart charge fault condition messages
CHECK BATTERY CONNECTIONS - When this message
appears, the most common cause is a poor connection to
the battery.
X Observing the “Safety instructions” at the front of this
manual, disconnect mains cord and the battery
clamps (4), clean the battery terminals and reconnect. If
the situation persists, we recommend taking your
battery to a certified automotive service centre for
evaluation.
REPLACE OR SERVICE BATTERY - The battery being
charged either has an internal open circuit, a shorted cell or
is highly sulphated and cannot accept a normal charge
current. We recommend taking your battery to a certified
automotive service centre for evaluation.
COOL DOWN CYCLE - red LED lit -The ventilation grill that
allows the air from flowing in and out of the charger may be
blocked.
X Make sure there is ample ventilation before resuming
operation.
REVERSE CLAMPS ON TERMINALS - The red LED lights
and a continuous warning tone sounds.
The connections to the battery’s positive and negative
terminals are incorrect.
X Observing the “Safety instructions” at the front of this
manual, disconnect the mains cord and the battery
clamps (4) and reconnect the clamps as described in
the section “Charging the battery”.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Black Decker BDSBC25A T1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Black Decker BDSBC25A T1

Black Decker BDSBC25A T1 Bedienungsanleitung - Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch - 104 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info