Bedienungsanleitung Black Decker BDV080 (Seite 5 von 12) (Englisch)

53623

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Features

1. Charge rate selector switch

2. Charging indicators

3. Battery clamps

4. Ring terminals

5. DC accessory plug

6. In-line connector

Connecting the battery charger

When all the preparations for charging and personal safety

have been completed, proceed as follows:

X For most automotive and similar applications the battery

charger may be connected to the battery while it is

connected to the dc circuit. If this is acceptable follow the

instructions given in "Charging a battery installed in the

circuit".

X If the battery must be disconnected from the circuit before

charging, follow the instructions given in "Charging a

battery disconnected from the circuit".

Warning! A marine (boat) battery must be removed and

charged on shore. To charge it on-board requires equipment

specially designed for marine use.

Charging a battery installed in the circuit.

Incorrect connection, battery short circuit, location of battery

and location of the battery charger may create a hazard.

Make sure that adequate preparation has been made before

proceeding.

Warning! If the battery posts cannot be accessed or the battery

charger clamps will contact the bodywork or components

adjacent to the battery, the battery must be removed before

charging. Follow the manufacturer's instructions to remove the

battery.

Check the polarity of the battery posts. A positive (POS, P, +)

battery post usually has a larger diameter than the negative

(NEG, N, -) battery post.

Follow the manufacturers' instructions to remove any

insulating covers from the battery posts.

Connect the positive (red) clamp from the battery charger to

the positive (POS, P, +) post of the battery.

Connect the negative (black) clamp from the battery charger

to the negative (NEG, N, -) post of the battery.

When disconnecting the battery charger from the battery,

always:

X Switch off and unplug the battery charger.

X Remove the negative (black) clamp first.

X Remove the positive (red) clamp last.

X Refit any insulating covers to the battery posts.

Charging a battery disconnected from the circuit.

Warning! Incorrect connection, battery short circuit, location of

battery and location of the battery charger may create a hazard.

Make sure that adequate preparation has been made before

proceeding.

If the battery is not already removed from the circuit, follow

the manufacturers' instructions to remove the battery before

charging.

Check the polarity of the battery posts. A positive (POS,P, +)

battery post usually has a larger diameter than the negative

(NEG, N, -) battery post.

Connect the positive (red) clamp from the battery charger to

the positive (POS, P, +) post of the battery.

Connect the negative (black) clamp from the battery charger

to the negative (NEG, N, -) post of the battery.

When disconnecting the battery charger from the battery,

always:

X Switch off and unplug the battery charger.

X Remove the negative (black) clamp first.

X Remove the positive (red) clamp last.

X Refit any insulating covers to the battery posts.

Use

Connecting the appliance with the battery clamps

(fig. A)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

X Connect the battery clamps (3) to the battery charger with

the in-line connector (6).

X The appliance's output leads have colour-coded battery

clamps (3) (red-positive and black-negative). These connect

directly to the corresponding connectors on the battery

terminals.

X Follow the steps outlined in "Safety instructions" at the

front of this manual.

X Insert the ac plug of the battery charger into an ac mains

socket.

Connecting the appliance with the ring terminals

(fig. A & B)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

X Connect the ring terminals (4) to the battery charger with

the in-line connector (6).

X The output leads have crimped, colour-coded ring terminals

(4) (red-positive and black-negative). The ring terminals (4)

connect directly to the corresponding connectors on the

battery terminals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV080 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV080

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info