Bedienungsanleitung Black Decker BEBLV301 (Seite 12 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

700090

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

(Original instructions)

Switch on the appliance by pushing the On/Off switch

(1) upwards (fig.j insert) and use a sweeping motion; the

debris/leaves will be sucked up the tube, and thrown into

the collection bag (10) (fig. J).

u As the bag lls, the power of the suction will decrease,

switch off the appliance and unplug from the mains power

supply.

u Unclip the the catch (10a) on the back pack collection bag

(g K).

u Unfold the opening of the back pack collection pack (g L).

u Open the back pack collection pack (g M) and proceed to

empty its contents.

u To seal the collection bag, hold the exible bars together

and roll 2-3 times (g N).

u Latch the retaining clip (10a) as shown in gure O.

Warning! Never remove the collection bag without rst turning

off and unplugging the appliance.

Note: If the suction decreases and the bag is not full, the

vacuum tube is probably clogged with debris. Turn off and

unplug the vacuum and clear the tube before continuing.

u When task is complete, rotate the assembled vacuum

tube anticlockwise to release the bayonet fixing. Insert the

rod (14) into the fan guard release (13) and push upwards

to release the assembled vacuum tube. Remove the

assembled vacuum tube from the powerhead as shown in

figure P.

u Replace the fan guard assembly as shown in figure Q.

u Rotate the fan guard assembly clockwise as shown in

gure R.

Blower mode (g. S, T, U, V)

u Assemble the upper blow tube (7), the lower blow tube (8)

and the optional concentrator (9) as shown in figure S.

u Push the assembled blow tube onto the vacuum outlet

(11a) until the lock engages tightly with the blow tube as

shown in figure T.

Warning! Never operate in Blow mode without the blow tube

firmly in place.

u Hold the blow tube approximately 180 mm above the

ground, switch on the appliance and using a sweeping

motion from side to side, advance slowly keeping the

accumulated debris/leaves in front of you (fig. U).

u Once you have blown the debris/leaves into a pile, you

can remove the blow tube assembly by inserting the rod

(14) into the aperture on the vacuum head and pushing

down to release the lock as shown in figure V.

u Now you can convert to vacuum mode and collect the

debris.

Troubleshooting

Problem Possible solution

Failure to operate

Check the connection to the power supply

Check the fuse in the plug, if blown, replace

(UK only).

Check that the blow/vacuum tube assembly is

correctly tted to the powerhead.

If the fuse continues to blow - immediately

disconnect from the mains power supply and

consult your local BLACK+DECKER

authorisedrepair agent.

Poor vacuum/high

pitched whine

Switch off - disconnect from the mains power

supply, debris should fall clear of the tube.

Remove and empty the collection bag.

Check that both the inlet and exit ports on the

vacuum tube are clear.

Remove any debris from the fan area.

If poor vacuuming continues - immediately

disconnect from the mains power supply and

consult your local BLACK+DECKER

authorised

repair agent

Maintenance

Your BLACK+DECKER appliance has been designed

to operate over a long period of time with a minimum of

maintenance.

Continuous satisfactory operation depends upon proper

appliance care and regular cleaning.

u Keep the appliance clean and dry.

u Remove any leaves stuck to the inside of the vacuum

tube.

u Regularly clean the ventilation slots with a clean, dry paint

brush.

u Regularly clean the collection bag and ensure that it is

clean and empty after each use.

u To clean the appliance, use only mild soap and a damp

cloth. Never let any liquid get inside the tool and never

immerse any part of the tool into liquid. Do not use any

abrasive or solvent-based cleaner.

u Self lubricating bearings are used in your product,

therefore lubrication is not required.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BEBLV301 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info