Bedienungsanleitung Black Decker BES700 (Seite 16 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709449

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

ENGLISH

(Original instructions)

Alternative method for cutting crown molding

Place the molding at an angle between the fence (12) and the

saw table (11), with the top side of the molding on the table

and the bottom side of the molding on the fence as shown

in gure S2.

The advantage to cutting crown molding using this method

is that no bevel cut is required. Minute changes in the miter

angle can be made without affecting the bevel angle. This

way,when corners other than 90º are encountered, the saw

can be quickly and easily adjustedfor them.

Instructions for cutting crown molding angled

between the fence and base of the saw for all cuts

This saw can cut up to 14 mm x 92 mm crown molding nested.

u Angle the molding so the bottom of the molding (part

which goes against the wall when installed) is against the

fence (12) and the top of the molding is resting on the saw

table (11), as shown in gure S2.

u The angled “ats” on the back of the molding must rest

squarely on the fence and saw table.

Inside Corner Outside Corner

Left Side Miter right at 45°

Save right side of cut

Miter left at 45°

Save right side of cut

Right Side Miter left at 45°

Save left side of cut

Miter right at 45°

Save left side of cut

Special Cuts

Never make any cut unless the material is secured on the

table and against the fence.

Bowedmaterial(g.T1,T2)

When cutting bowed material always position it as shown in

gure T1 and never like that shown in gure T2. Positioning

the material incorrectly will cause it to pinch the blade near

the completion of the cut.

Cutting round material

Rounded material should be clamped or held rmly to the

fence to keep It from rolling. This is extremely important when

making angle cuts.

Cuttinglargematerial(g.U)

Occasionally you will encounter a piece of wood a little too

large to t beneath the lower guard.

To clear the guard over the wood, with the saw off and your

right hand on the operating handle, place your right thumb

outside of the upper portion of the guard and roll the guard up

just enough to clear the wood, as shown in gure U. Release

the guard prior to starting the motor. The guard mechanism

will function properly during the cut. Only do this when neces-

sary.

NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD

OPEN WHEN OPERATING THIS SAW.

Warning! Always be sure that the tool is switched off and

unplugged before adjusting or checking the tools function.

After use

u After use, wipe off chips and dust adhering to the tool with

a cloth or the like.

u Keep the blade guard clean according to the directions in

the previously covered section.

u Lubricate the sliding portions with machine oil to prevent

rust.

u When storing the tool, pull the carriage toward you fully.

Carrying the tool

u Make sure the tool is unplugged.

u Secure the blade at the 0° bevel angle and turn the base

to the right mitre angle fully with the slide bar locking scre

(28).

u Secure the slide bars after pulling the carriage toward you

fully.

u Lower the handle fully and lock it in the position by

pushing in the saw head locking pin (17).

u Carry the tool by holding the carry handle (22).

u If you remove the clamp, dust bag, etc., you can carry the

tool more easily.

u Carry the tool by one hand holding the carrying handle

(22) and one hand holding the tool base.

Caution! Always secure all moving portions before carrying

the tool.

Saw head locking pin (17) is for carrying and storage

purposes only and not for any cutting operations.

Troubleshooting

Problem Possible Cause Solution

Motor does

not start

Saw not plugged in. Check that all cords are plugged in.

Angle of cut

inaccurate

Mitre table

unlocked.

Use mitre table locking lever (see

Adjusting the mitre angle section.

Too much sawdust

under table.

Vacuum or blow out dust. Wear eye

protection.

Cutting arm

cannot fully

raise, or blade

guard cannot

fully close

Parts Failure. Contact service centre.

Pivot spring not

replaced properly

after service.

Contact service centre.

Sawdust build up. Clean and lubricate moving parts.

Saw head locking

pin not set properly.

Check, adjust, and properly set saw

head locking pin.

Blade binds,

jams or

shakes

Saw blade

damaged.

Replace blade.

Dull blade. Replace or sharpen blade.

Improper blade. Replace blade.

Warped blade. Replace blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BES700 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info