709488

Black Decker BESTA530 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
11
ENGLISH
(Original instructions)
Rewinding spool from bulk line (Fig. Q, R, S)
Replacement spools of cutting line are available from your
BLACK+DECKER dealer. Packs containing 3
spools of cutting line are also available.
Unplug the tool.
Remove the empty spool from the trimmer as described
in “REPLACING THE SPOOL”.
Remove any remaining cutting line from the spool.
Make a fold at the end of the cutting line at about 19mm
(21). Feed the cutting line into one of the line anchoring
slots (22) as shown in Fig. Q.
Note: Take care not to allow the the line on the spool to
unravel. Hold it rmly with one hand at all times.
Insert the 19mm end of the bulk line into the hole (23) in
the spool adjacent to the slot as shown in Fig. R. Make
sure the line is pulled tight against the spool as shown in
Fig. S.
Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (Fig. S).
When the wound cutting line reaches the recesses (24),
cut the line. (Fig. R).
Fit the spool onto the trimmer as described in
“REPLACING THE SPOOL.
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Machine runs slowly
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
Check that the cutting line does not protrude more than
approximately 136mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade.
Automatic line feed does not work
Remove the spool cap.
Pull the cutting line until it protrudes approximately 136mm
from the spool. If insufcient cutting line is left on the
spool, install a new spool of cutting line.
Ensure that the line is not crisscrossed on the spool as
detailed in Fig. S. If it is, unwind the cutting line, then wind
it back on the spool neatly so that the lines do not cross.
Ensure the beginning of the cutting line is pulled tight
against the spool as shown in Fig. S.
Align the tabs on the spool cap with the cut outs in the
housing.
Push the spool cap onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade. If the automatic
line feed still does not work or the spool is jammed, try the
following suggestions:
Carefully clean the spool and housing.
Remove the spool and check if the lever in the spool
housing can move freely.
Remove the spool and unwind the cutting line,
then wind it on neatly again. Replace the spool into
the housing.
Maintenance
Your BLACK+DECKER corded/cordless machine/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/machine care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the machine/tool.
Or switch off and remove the battery from the machine/
tool if the machine/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/machine
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Black Decker BESTA530 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info