Bedienungsanleitung Black Decker BHD5 (Seite 19 von 98) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

15916

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

ENGLISH

• Push the drill bit into a surface at a right angle

and adjust the depth adjustment rod (11) as

shown.

• Tighten the clamp nut (17).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool

(approx. 20 kg). Excessive force does

not speed up drilling or chiselling but

decreases tool performance and may

shorten tool life.

Drilling with a solid bit (fig. A)

• Set the electronic speed and impact control dial (2).

• Set the mode selector lever (4) to the

„hammer drilling“ position.

• Insert the appropriate drill bit.

• Fit and adjust the side handle (8).

• If necessary, set the drilling depth.

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and press the

ON/OFF-switch (1).

• To stop the tool, release the ON/OFF-switch (1).

Always switch off the tool when work is finished

and before unplugging.

Drilling with a core bit (fig. A)

• Turn the electronic speed and impact control dial

(2) to medium or high speed position.

• Set the mode selector lever (4) to the

„hammer drilling“ position.

• Fit and adjust the side handle (8).

• Insert the appropriate core bit.

• Assemble the centerdrill into the core bit.

• Place the centerdrill on the spot and press the

ON/OFF-switch (1). Drill until the core penetrates

into the concrete approx. 1 cm.

• Stop drilling and remove the centerdrill. Place the

core bit back into the hole and continue drilling.

• When drilling through a structure thicker than

the depth of the core bit, break away the round

cylinder of concrete or core inside the bit at

regular intervals.

To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of

the centerdrill completely through the

structure. Then drill the cored hole halfway

from each side.

• To stop the tool, proceed as described above.

Chipping and chiselling (fig. A)

• Set the electronic speed and impact control dial (2).

• Select the type of operation – Turn the option

level (5) to “cut only”.

• Insert the appropriate chisel and rotate it by hand

to lock it into one of 8 positions.

• Fit and adjust the side handle (8).

• Press the ON/OFF-switch (1) and start working.

• To stop the tool, proceed as described above.

Various types of SDS-max

drill bits and chisels are

available as an option.

Consult BERNER for further information on the

appropriate accessories.

Maintenance

Your BERNER Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

• The Rotary Hammer is not user-serviceable.

Take the tool to an authorized BERNER repair

agent as soon as the service indicator LED (3)

lights up.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly

clean the housing with a soft cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BHD5 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info