Bedienungsanleitung Black Decker CD115 T3 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578558

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

u Place the guard (4) onto the tool as shown.

u Place the ange (8) over the spindle with the protruding

pips towards the guard. Make sure that the holes in the

ange align with the screw holes.

u Secure the ange with the screws (9). Make sure that the

screws are fully tight and that the guard can be rotated.

Removing

u Use a screwdriver to remove the screws (9).

u Remove the ange (8), guard (4) and spring washer (7).

Store these parts carefully.

Warning! Never use the tool without the guard.

Fitting the side handle

u Screw the side handle (2) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs

(g.C-E)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size

(see technical data).

Fitting

u Fit the guard as described above.

u Place the inner ange (10) onto the spindle (5) as shown

(g. C). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (11) onto the spindle (5) as shown (g. C).

If the disc has a raised centre (12), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner ange.

u Place the outer ange (13) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. D). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. D).

u Keep the spindle lock (3) depressed and tighten the outer

ange using the two-pin spanner (14) (g. E).

Removing

u Keep the spindle lock (3) depressed and loosen the outer

ange (13) using the two-pin spanner (14) (g. E).

u Remove the outer ange (13) and the disc (11).

Fittingandremovingsandingdiscs(g.E&F)

For sanding, a backing pad is required. The backing pad is

available from your Black & Decker dealer as an accessory.

Fitting

u Place the inner ange (10) onto the spindle (5) as shown

(g. F). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the backing pad (15) onto the spindle.

u Place the sanding disc (16) onto the backing pad.

u Place the outer ange (13) onto the spindle with the raised

centre facing away from the disc.

u Keep the spindle lock (3) depressed and tighten the outer

ange using the two-pin spanner (14) (g. E). Make sure

that the outer ange is tted correctly and that the disc is

clamped tightly.

Removing

u Keep the spindle lock (3) depressed and loosen the outer

ange (13) using the two-pin spanner (14) (g. E).

u Remove the outer ange (13), the sanding disc (16) and

the backing pad (15).

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting disc.

Switching on and off

u To switch on, slide the on/off switch (1) forward. Note that

the tool will continue running when you release the switch.

u To switch off, press the rear part of the on/off switch.

Warning! Do not switch the tool off while under load.

Hints for optimum use

u Firmly hold the tool with one hand around the side handle

and the other hand around the main handle.

u When grinding, always maintain an angle of approx. 15°

between the disc and the workpiece surface.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD115 T3 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info