Bedienungsanleitung Black Decker CD601 T2 (Seite 8 von 16) (Englisch)

579731

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Mitre angle scale

6. Locking knob for mitre angle adjustment

7. Parallel fence

8. Shoe

9. Saw blade

10. Saw blade guard

11. Riving knife

12. Depth of cut scale

13. Locking knob for depth of cut adjustment

14. Spanner

15. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removing and tting a saw blade (g. A)

Caution! This method for changing the blade is only for use

with blades that contain a hole (16) for the purpose of locking

the blade whilst tting and removing.

Removing

u Insert a screwdriver into the hole (16) to prevent the saw

blade from rotating.

u Loosen and remove the blade retaining screw (17) by

turning it counterclockwise using the spanner (14) supplied.

u Remove the outer washer (18).

u Remove the saw blade (9).

Fitting

u Place the saw blade onto the inner washer (19), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (18) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (17) into the hole.

u Insert a screwdriver into the hole (16) to prevent the saw

blade from rotating.

u Securely tighten the blade retaining screw by turning it

clockwise using the spanner (14) supplied.

u Adjust the riving knife as described below.

Warning! Whenever a new blade is tted the saw blade guard

should be checked to ensure that it can move freely.

Removing and tting a saw blade (g. B)

Caution! This method is for changing blades that do not

contain a hole (16) for the purpose of locking the blade whilst

tting and removing.

Removing

u Set the depth of cut on the saw to 10mm.

u Place a plank of wood on the floor, then place the saw

onto the leading edge of the wood as shown in fig B to

prevent the blade from turning.

u Whilst applying firm pressure on the saw, loosen and

remove the blade retaining screw (17) by turning it

counterclockwise using the spanner (14) supplied.

u Remove the outer washer (18).

u Remove the saw blade (9).

Fitting

u Place the saw blade onto the inner washer (19), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (18) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (17) into the hole loosely

tighten by hand.

u Place a plank of wood on the floor, then place the saw

onto the leading edge of the wood as shown in fig B to

prevent the blade from turning.

u Whilst applying firm pressure on the saw, securely tighten

blade retaining screw (17) by turning it clockwise using the

spanner (14) supplied.

u Adjust the riving knife as described below.

Warning! Whenever a new blade is tted the saw blade guard

should be checked to ensure that it can move freely.

Adjusting the riving knife (g. C)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

u Loosen the screw (20) holding the riving knife in position.

u Position the riving knife (11) as shown.

The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD601 T2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CD601 T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info