Bedienungsanleitung Black Decker CD602 T2 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

579732

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

The height difference between the toothed rim and the lower

end of the riving knife should be 2 - 3 mm.

u Tighten the screw.

Fittingandremovingtheparallelfence(g.D)

The parallel fence is used to saw in a straight line parellel to

the edge of the workpiece.

Fitting

u Loosen the locking knob (21).

u Insert the parallel fence (7) through the openings (22).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob (21).

u Pull the parallel fence off the tool.

Use

This tool can be used in the right hand or the left hand.

Adjustingthedepthofcut(g.E)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2 mm.

u Loosen the knob (13) to unlock the saw shoe.

u Move the saw shoe (8) into the desired position. The

corresponding depth of cut can be read from the scale (12).

u Tighten the knob to lock the saw shoe in place.

Adjustingthemitreangle(g.F)

This tool can be set to mitre angles between 0° and 45°.

u Loosen the locking knob (6) to unlock the saw shoe.

u Move the saw shoe (8) into the desired position. The

corresponding mitre angle can be read from the scale (5).

u Tighten the locking knob to lock the saw shoe in place.

Switching on and off

u To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

u To switch the tool off, release the on/off switch.

Sawing

u Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Work with the shoe pressed against the workpiece.

Dustextraction(g.G)

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool. The adaptor can be purchased from your

local Black & Decker retailer.

u Insert the dust extraction adaptor (23) into the saw dust

outlet (15).

u Connect the vacuum cleaner hose to the adaptor.

Hints for optimum use

u As some splintering along the line of cut on the top side of

the workpiece cannot be avoided, cut on the side where

splintering is acceptable.

u Where splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of plywood onto the top of the

workpiece.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior (when fitted).

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD602 T2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CD602 T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info