Bedienungsanleitung Black Decker CD602 T2 (Seite 7 von 92) (Polnisch)

579732

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

take corrective actions to eliminate the cause of

blade binding.

c. When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from

the workpiece as the saw is restarted.

d. Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed

under the panel on both sides, near the line of cut

and near the edge of the panel.

e. Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade

binding and kickback.

f. Blade depth and bevel adjusting locking levers

must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

g. Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions for circular saws with outer

or inner pendulum guards and with tow guard

a. Check lower guard for proper closing before

each use. Do not operate the saw if lower guard

does not move freely and close instantly.

Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped,

lower guard may be bent. Raise the lower guard

with the retracting handle and make sure it moves

freely and does not touch the blade or any other

part, in all angles and depths of cut.

b. Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up

of debris.

c. Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must be

released. For all other sawing, the lower guard

should operate automatically.

d. Always observe that the lower guard is

covering the blade before placing saw down

on bench or ﬂ oor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is

released.

Additional safety instructions for all saws with

riving knife

a. Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must

be thicker than the body of the blade but thinner

than the tooth set of the blade.

b. Adjust the riving knife as described in

this instruction manual. Incorrect spacing,

positioning and alignment can make the riving

knife ineffective in preventing kickback.

c. Always use the riving knife except when

plunge cutting. Riving knife must be replaced

after plunge cutting. Riving knife causes

interference during plunge cutting and can create

kickback.

d. For the riving knife to work, it must be engaged

in the workpiece. The riving knife is ineffective

in preventing kickback during short cuts.

e. Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing rate

of a guard.

Residual risks

The following risks are inherent to the use of saws:

- Injuries caused by touching the rotating parts

Even with the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts

of the rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ﬁ ngers when opening the

guards.

- Health hazards caused by breathing dust

developed when sawing wood, especially oak,

beech and MDF.

Saw blades

 Do not use blades of larger or smaller diameter

than recommended. For the proper blade rating

refer to the technical data. Use only the blades

speciﬁ ed in this manual, complying with EN 847-1.

 Warning! Never use abrasive wheels.

Safety of others

 Warning! Wear ear protection when using this

tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD602 T2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CD602 T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info