Bedienungsanleitung Black Decker CD700 T1 (Seite 23 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577916

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

buildings may have been painted in the past with

paint containing lead and covered by additional

layers of paint. Once deposited on surfaces, hand to

mouth contact can result in the ingestion of lead.

Exposures to even low levels of lead can cause

irreversible brain and nervous system damage; young

and unborn children are particularly vulnerable. Do

not smoke, eat or drink in a work area that could or

may be contaminated by lead. Lead based paints

should only be removed by a professional and

should not be removed using a heatgun.

• When removing paints you should ensure that your

work area is enclosed. It is advisable to wear a dust

mask.

• Do not burn the paint. Use the integral scraper

where supplied otherwise keep the nozzle at least

25mm (1”) from the surface as this keeps the

temperature below the required 450˚C. If you are

scraping from a vertical position then you should

scrape downwards to prevent the paint from falling

back into the heatgun and burning. Dispose of all

paint debris safely and ensure that the work area is

thoroughly cleaned after completing the job.

• Do not use in a damp atmosphere or where

flammable gases may be present or use near

combustible materials. Spaces behind boards,

ceilings and floors and wall cavities in timber frame

constructed houses can contain flammable

materials. Check before using the heatgun.

• Allow the tool to cool fully before storing.

• Ensure adequate ventilation when using heatguns

as toxic fumes may be produced.

• Do not use as a hairdryer! The air temperature is far

higher than a hairdryer.

• Do not obstruct either the air intake or nozzle outlet

as this may cause excessive heat build up resulting

in damage to the tool.

• Do not direct the hot air blast at other people.

• Do not touch the metal nozzle as it gets very hot during

use and remains hot for up to 30 minutes after use.

• Do not place the nozzle against anything while using

or immediately after use.

• Do not poke anything down the nozzle as it could

give you an electric shock. Do not look down the

nozzle while the unit is working because of the high

temperatures being produced.

• Do not allow paint to adhere to the nozzle or

scraper as it could ignite after a time.

• Do not operate your heatgun whilst it is hanging by

the hanging ring.

Save these instructions!

DOUBLE INSULATION

The tool is double insulated. This means that all

the external metal parts are electrically insulated

from the mains power supply. This is done by

placing insulation barriers between the

electrical and mechanical components making

it unnecessary for the tool to be earthed.

Note: Double insulation does not take the place

of normal safety precautions when operating the

tool. The insulation system is for added protection

against injury resulting from a possible electrical

insulation failure within the tool.

ELECTRICAL SAFETY

Be sure the supply is the same as the voltage given on

the rating plate. The tool is fitted with a two-core cable

and plug.

MAINS PLUG REPLACEMENT (UK ONLY)

Should the mains plug need replacing and you are

competent to do this, proceed as instructed below.

If you are in doubt, contact a Black & Decker service

agent or a qualified electrician.

• Disconnect the plug from the power supply.

• Cut off the plug and dispose of safely. A plug with

bared copper conductors is very dangerous if

engaged in a live socket outlet.

• Only fit BS1363A approved plugs fitted with the

correctly rated fuse. Note: Fuses do not give

personal protection against electric shock.

• The cable wire colours, or a letter, will be marked at

the connection point of most good quality plugs.

Attach the wires to their respective points in the

plug (see diagram). Brown is L (live) and blue is

N (neutral).

Fit a plug

approved

to BS1363A

Connect

blue to

N (neutral)

Make sure that

the outer sheath

of the cable is held

firmly by the clamp

Fit a 5 amp fuse

Connect

brown to

L (live)

230 volts AC

only. Never use

a light socket

• Before replacing the top cover of the plug ensure

that the cable restraint is holding the outer sheath of

Fit a 13 amp fuse

CD700 KX1600-1683 ML p22-39 07/01/2000, 3:39 pm23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD700 T1 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info