Bedienungsanleitung Black Decker CHS6000A TH1 (Seite 7 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

581135

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Labels on tools

Features

1. Shoe

2. Lock-off button

3. Charging socket

4. On/Off switch

5. Blade clamp release lever

6. Charger plug

7. Charger

Assembly

Fitting and removing a saw blade (fig. A)

The tool accepts both T-shank and universal shank jig saw

blades.

Fitting:

 Push down on the blade clamp release lever (5) to its fully

open position.

 Insert the blade shank (8) from the front.

 Release the blade clamp release lever (5).

Removing:

 Push down on the blade clamp release lever (5) to its fully

open position.

 Remove the blade.

 Release the blade clamp release lever (5).

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These include:

 Injuries caused by touching any rotating/moving parts.

 Injuries caused when changing any parts, blades or

accessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods make sure you take

regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF).

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. B)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become

warm while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 10°C or above 40°C. Recommended charging

temperature is approximately 24°C.

 To charge the battery, insert the charger plug (6) into the

charging socket (3).

 Plug in the charger (7) and switch on at the mains.

 Leave the tool connected to the charger for 6-8 hours.

 The charger may hum and become warm while charging;

this is normal and does not indicate a problem.

Generally, a charging time of 6 hours will enable the tool to

operate at an effective power level for most tasks. However,

further charging for up to 8 hours could significantly increase

the run time, depending on the battery and the charging

conditions.

 Before using the tool, unplug the charger (7) and

disconnect the tool from the charger.

 Do not use the tool while it is connected to the charger.

Switching on and off (fig. C)

To switch the tool on, push the lock-off button (2) to the

unlock position and squeeze the on/off switch (4).

 To switch the tool off, release the on/off switch (4).

Sawing (fig. D)

Hold the tool firmly with both hands while cutting.

The shoe (1) should be held firmly against the material being

cut. This will help to prevent the saw from jumping, reduce

vibration and minimise blade breakage.

 Let the blade run freely for a few seconds before starting

the cut.

 Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Sawing laminates

Because the saw blade cuts on the upward stroke,

splintering may occur on the surface closest to the shoe

plate.

 Use a fine-tooth saw blade.

 Saw from the back surface of the workpiece.

 To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CHS6000A TH1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CHS6000A TH1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info