Bedienungsanleitung Black Decker CLM3820 T1 (Seite 12 von 20) (Englisch)

586103

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

(Original instructions)

Fitting the grass collection box (g. I & J)

u Lift the clear grass ap (12) and place the grass collection

box (9) over the lugs (20).

Wheel height adjustment (g. K & L)

Your mower features the Black & Decker Easy - height adjust-

ment system. This system will adjust all four wheels at the

same time.

The mower has six blade height adjustment positions (30 mm

to 80 mm). Refer to the scale on the side of the mower. The

pointer will indicate the height setting for cutting your lawn.

This setting can be a reference for the next time you want to

cut your lawn to the same height.

u Release the bail bar (2) to turn the lawnmower off, wait

until the blade stops and remove the safety key (1).

u To raise or lower the cutting height, place the palm of your

hand on the palm rest (21) and pull the height adjustment

lever (13) away from the mower body.

u Move the height adjust lever (13) into the required position

then push it back in towards the mower body.

Note: Make sure that the mower is securely locked in one of

the six positions.

Removing and tting the battery (g. O)

Before removing the battery:

u Place the mower on level ground.

u Release the bail bar (2) to turn the mower off, wait for the

blade to stop and remove the safety key (1).

To remove the battery:

u Pull the battery cover release (15) towards the front of the

mower body and lift the battery cover (14).

u Lift the battery (22) out of the mower.

To t the battery

u Pull the battery cover release (15) towards the front of the

mower body and lift the battery cover (14).

u Slide the battery (22) into the mower. (the battery will only

t one way.)

Use

Warning! Let the appliance work at its own pace. Do not

overload.

Charging the battery (g. M)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (22), insert it into the charger (23).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (24) will ash green continuously

(slowly).

The charge is complete when the charging indicator (24)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops off the battery charge. The charging indica-

tor (24) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (24) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (22).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original bat-

tery is defective and should be returned to a service centre

for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

State of charge indicator (g. N)

The battery is tted with a state of charge indicator. This can

be used to display the current level of charge in the battery

during use and during charging.

u Press the state of charge indicator button (25).

Safety key (g. P)

Remove the safety key:

u Whenever leaving the appliance unattended.

u Before cleaning a blockage.

u Before checking, cleaning or working on the appliance.

u After striking a foreign object.

u Whenever the appliance starts vibrating abnormally.

Switching on and off (g. P & Q

Warning! Sharp moving blade. Never attempt to override the

operation of this switch and safety key system as a serious

injury could result.

Switching on

u Insert the safety key (1) fully into the switch housing.

u Push the lock off release button (3) on the top of the

switch housing.

u Pull the blade bail bar (2) toward the handle bar (4).

Black Decker CLM3820 T1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CLM3820 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info