Bedienungsanleitung Black Decker CLM5448PC (Seite 13 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709481

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

The completion of charge is indicated by the

green LED remaining on continuously. The pack

is fully charged and may be used at this time or

left on the charger

Warning! Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source.

Problems are indicated by one LED ashing in different

patterns.

Bad battery

The charger can detect a weak or damaged

battery.

The red LED ashes in the pattern indicated

on the label. If you see this bad battery blink pattern, do not

continue to charge the battery.

Return it to a service center or a collection site for recycling

Hot/cold pack delay

When the charger detects a battery that

is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery has normalized.

After this happens, the charger automatically switches to the

Pack Charging mode. This feature ensures maximum battery

life. The red LED ashes in the pattern indicated on the label

when the hot / cold pack delay is detected

Important charging notes

u Longest life and best performance can be obtained if the

battery pack is charged when the air temperature is

between 60°F and 80°F (16°- 27°C).

u DO NOT charge the battery pack in an air temperature

below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the

battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem.

To facilitate the cooling of the battery pack after use, avoid

placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 60°F -

80°F (16° - 27°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these condi-

tions. Follow the charging procedure. You may also charge

a partially used pack whenever you desire with no adverse

affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger.

NEVER ATTEMPT TO OPEN THE BATTERY PACK FOR

ANY REASON. IF THE PLASTIC HOUSING OF THE

BATTERY PACK BREAKS OR CRACKS, RETURN TO A

SERVICE CENTER FOR RECYCLING.

Battery state of charge indicator

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery while in the mower and during charging. It does not

indicate tool functionality and is subject to variation based on

product components, temperature and end-user application.

Checking state of charge:

u Press the state of charge indicator button (A1).

u The three LEDs (A2) will illuminate indicating the percent

of charge in the battery. See chart in gure A.

u If LED light does not illuminate, charge battery.

Installing and removing the battery packs

Warning! Make certain the Safety key is removed to prevent

Actuation before removing or Installing battery.

To install battery packs:

u Lift the battery port cover (12) up to expose the battery

port (15).

u Slide the battery (16) into the battery port until it is fully

seated and an audible click is heard (gure B).

Make sure battery pack is fully seated and fully latched

into position. Repeat process for the second battery port.

u Close the battery port cover. Ensure the cover is fully

latched before starting mower.

To remove battery packs:

u Open the battery port cover (12) as described above.

u Depress the battery release button (16a) on the battery

pack and pull battery pack out of tool as shown in gure C.

POWERCOMMAND battery pack selection

Warning! Make certain the Safety key is removed to prevent

Actuation before selecting active battery.

The mower is equipped with a POWERCOMMAND battery

selection button (11). This is used to extend runtime. Press the

battery selection button (gure D) on the left or right.

u The side marked “1” activates the left side battery port.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CLM5448PC Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info