Bedienungsanleitung Black Decker CS1250L (Seite 5 von 7) (Englisch)

709473

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Labels on tool

The following symbols are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the

user must read the instruction manual.

Wear safety glasses or goggles.

Wear ear protection.

Wear a dust mask.

No Hands Zone - Keep ngers and arms

away from rotational saw blades.

Wear gloves when handling saw blades.

Laser radiation.

Do not look into the laser beam.

Do not use optical tools to view the laser

beam.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on

the rating plate. Never attempt to replace the

charger unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Mitre angle scale

6. Locking knob for mitre angle adjustment

7. Parallel fence

8. Shoe

9. Saw blade

10. Saw blade guard

11. Depth of cut scale

12. Locking knob for depth of cut adjustment

13. Saw dust outlet

14. Saw blade hex wrench

21. Spindle lock button

Figures G & H (CS1250L model only)

20. Laser sight

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removing and tting a saw blade (g. B)

Removing

u Keep the spindle lock button (21) depressed and rotate

the blade until the spindle lock engages.

u Loosen and remove the blade retaining screw (15) by

turning it counterclockwise using the hex wrench (14).

u Remove the outer washer (16).

u Remove the saw blade (9).

NOTICE: Never engage the spindle lock while the saw is

running. Never turn the saw on while the spindle lock is

engaged. Severe damage to the saw may result.

Fitting

u Keep the spindle lock button (21) depressed and rotate

the blade until the spindle lock engages.

u Loosen and remove the blade retaining screw (15) by

turning the hex wrench (14) counterclockwise.

u Remove the outer washer (16).

u Place the saw blade (9) onto the spindle shaft, making

sure that the arrow on the blade points in the same direc-

tion as the arrow on the upper gaurd of the tool.

u Fit the outer washer on the spindle with the larger at

surface against the blade.

u Insert the blade retaining screw into the hole in the

spindle.

u Securely tighten the blade retaining screw by turning hex

wrench clockwise to tighten the blade retaining screw.

Warning! Whenever a new blade is tted the saw blade guard

should be checked to ensure that it can move freely.

Warning! To reduce the risk of serious personal injury, read,

understand and follow all important safety warnings and

instructions prior to using tool.

Fitting and removing the parallel fence (g. C)

The parallel fence is used to saw in a straight line parellel to

the edge of the workpiece.

Fitting

u Loosen the locking knob (18).

u Insert the parallel fence (7) through the openings (19).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob (18).

u Pull the parallel fence off the tool.

Use

This tool can be used in the right hand or the left hand.

Warning! Let the tool work at its own pace. Do not overload.

Electronic Function. Laser beam action. Model

CS1250L only (Fig.G, H)

Caution! When not in use, be sure to turn off the laser.

Never look into the laser beam directly; laser beam may injure

your eyes.

LASER RADIATION: DO NOT STARE INTO THE BEAM or

any CLASSII LASER PRODUCTS.

Before shifting the laser line or performing maintenance

adjustment, be sure to unplug the tool.

u To turn the laser on/off, toggle the switch (12a) on the

back of the laser housing.

Cleaning of the lens for the laser light

If the lens for the laser light becomes dirty, or sawdust ad-

heres to it in such a way that the laser line is no longer easily

visible, unplug the saw and clean the lens carefully with a

damp, soft cloth. Do not use solvents or any petroleum based

cleaners on the lens.

Note: When laser line is dim and almost or entirely invisible

because of the direct sunlight in the indoor or outdoor window

near your work area, relocate the work area to a place not

exposed to direct sunlight.

Note: All of the adjustments for the operation of this machine

have been carried out at the factory.

Caution: Use of controls or adjustments or performance of

procedures other than those specied herein may result in

hazardous radiation exposure. The use of optical instruments

with this product will increase eye hazard. Do not attempt to

repair or disassemble the laser. If unqualied persons attempt

to repair this laser product, serious injury may result.

Any repair required on this laser product should be performed

by authorised service centre personnel.

Adjusting the depth of cut (g. D)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx.

2 mm.

u Loosen the knob (12) to unlock the saw shoe.

u Move the saw shoe (8) into the desired position. The

corresponding depth of cut can be read from the scale

(11).

u Tighten the knob to lock the saw shoe in place.

Adjusting the mitre angle (g. E)

This tool can be set to mitre angles between 0° and 45°.

u Loosen the locking knob (6) to unlock the saw shoe.

u Move the saw shoe (8) into the desired position. The

corresponding mitre angle can be read from the scale (5).

u Tighten the locking knob to lock the saw shoe in place.

Switching on and off

u To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

u To switch the tool off, release the on/off switch.

Sawing

u Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Work with the shoe pressed against the workpiece.

Dust extraction (g. F)

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool. The adaptor can be purchased from your

local BLACK+DECKER retailer.

u Insert the dust extraction adaptor into the saw dust

outlet (13).

u Connect the vacuum cleaner hose to the adaptor.

Hints for optimum use

u As some splintering along the line of cut on the top side of

the workpiece cannot be avoided, cut on the side where

splintering is acceptable.

u Where splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of plywood onto the top of the

workpiece.

Accessories

The performance of your tool depends on the accessory used.

BLACK+DECKER and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

Black Decker CS1250L Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info