Bedienungsanleitung Black Decker CS143K T1 (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581137

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

◆ Make sure the blade is securely fitted by trying to remove

it without depressing the blade release button (3).

If you are unable to fit the blade, check if the location pin is in

the correct position as shown in fig. E. If it is not, keep the

blade release button depressed and use a screwdriver to turn

the location pin into the correct position.

Removing

◆ Keep the blade release button (3) depressed and rotate

the blade downward through 90°.

◆ Take the blade sideways off the location pin and slide it

out of the tool.

◆ Release the blade release button.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. A)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become warm

while charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Using the 3 hr charger

◆ To charge the battery (4), remove it from the tool.

◆ Slide the charger receptacle (6) onto the battery.

◆ Plug in the charger (5).

After approx. 3 hours of charging, the battery will be sufficiently

charged for use in regular applications. After approx. 6 hours

of charging, the battery will be fully charged.

◆ Remove the charger receptacle from the battery.

Using the 1 hr charger

◆ To charge the battery (4), remove it from the tool and

insert it into the charger (7). The battery will only fit into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (8) lights up. If the

green end of charge indicator (9) lights up now instead,

the battery is too hot and cannot be charged. If this

happens, remove the battery from the charger, let the

battery cool down for approx. 1 hour and re-insert it.

After approx. 1 hour of charging, the red charging indicator (8)

will stop lighting and the green end of charge indicator (9) will

light up. The battery is now fully charged.

◆ Remove the battery from the charger.

Switching on and off (fig. F)

◆ To switch the tool on, push the two lock-off button (2) into

the unlock position and squeeze the variable speed switch

(1).

◆ To switch the tool off, release the variable speed switch.

Sawing (fig. G)

◆ If possible, always hold the tool with both hands.

◆ Let the blade run freely for a few seconds before starting

the cut.

◆ Apply only a gentle pressure to the tool while performing

the cut.

◆ Use the same back and forth movement you would

employ with a normal hand saw. This enables a quicker

and cleaner cut.

Hints for optimum use

Sawing wood

◆ Clamp the workpiece securely and remove all nails and

metal objects.

◆ When splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of scrap wood or hardboard to

both sides of the workpiece and saw through this sandwich.

Sawing metal

◆ Be aware that sawing metal takes much more time than

sawing wood.

◆ Use a saw blade suitable for sawing metal. Use a fine-

tooth saw blade for ferrous metals and a coarser saw

blade for nonferrous metals.

◆ When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

◆ Spread a film of oil along the intended line of cut.

Cutting branches

◆ Cut downward and away from your body.

◆ Make the cut close to the main branch or tree body.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CS143K T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CS143K T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info