Bedienungsanleitung Black Decker CS355 T1 (Seite 5 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

579640

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

16. Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed

from the tool before operating the tool.

17. Avoid unintentional starting

Do not carry the tool with a nger on the switch. Be sure that

the tool is switched off before plugging in.

18. Use outdoor extension cables

Before use, inspect the extension cable and replace if

damaged. When using the tool outdoors, only use extension

cables intended for outdoor use and marked accordingly.

19. Stay alert

Watch what you are doing, use common sense and do not

operate the tool when you are tired.

20. Check for damaged parts

Before use, carefully check the tool and mains cable for

damage. Check for misalignment and seizure of moving

parts, breakage of parts, damage to guards and switches and

any other conditions that may affect its operation. Ensure that

the tool will operate properly and perform its intended function.

Do not use the tool if any part is damaged or defective. Do not

use the tool if the switch does not turn it on and off. Have any

damaged or defective parts replaced by an authorised Black

and Decker repair agent. Never attempt any repairs yourself.

21. Warning!

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present a

risk of personal injury.

22. Have your tool repaired by a qualied person

This tool is in accordance with the relevant safety regulations.

Have your tool repaired by an authorised Black and Decker

repair agent. Repairs should only be carried out by qualied

persons using original spare parts; otherwise this may result in

considerable danger to the user.

Additional safety instructions for chopsaws

u Always wear regular working gloves while operating this

tool.

u Keep hands away from the cutting disc. Never cut

workpieces that require manual action closer than 15 cm

from the rotating cutting disc.

u Do not cut workpieces less than 1.2 mm in thickness when

using the cutting disc supplied with this tool.

u Do not operate this tool without guards in place.

u Do not perform any operation freehand. Use the material

clamp to clamp the workpiece securely.

u Never reach in the back of the cutting disc.

u Always position the tool on a at, stable surface that is

well maintained and free of loose materials, e.g. chips and

cut-offs.

u Before using, inspect the cutting disc for cracks or aws.

Discard the cutting disc if a crack or aw is evident.

u Make sure the cutting disc is not contacting the workpiece

before the tool is switched on.

u In operation, avoid bouncing the cutting disc or giving it

rough treatment. If this occurs, stop the tool and inspect

the cutting disc.

u Do not operate the tool while standing in line with the

cutting disc. Keep other persons away from the work area.

u Be aware of cutting chips and the material being cut. They

may be sharp and hot. Allow cut off parts to cool before

handling.

u The spark deector becomes hot during use. Avoid

touching or adjusting the spark deector immediately after

operation.

u Switch off the tool and wait for the cutting disc to stop

before moving the workpiece or changing the settings.

u After switching off, never attempt to stop the cutting disc

by pressing against the side of the disc.

u Do not use cutting uids. These uids could ignite or

cause electrical shock.

u Check that the workpiece is properly supported.

u Use the cutting discs recommended by the manufacturer

only. Never use circular saw blades or any other types of

toothed blades.

u The max. allowable speed of the cutting disc must always

be equal to or greater than the no-load speed of the tool

specied on the nameplate.

u Do not use cutting discs that do not conform to the

dimensions stated in the technical data.

u Only use cutting discs that conform to EN12413.

u Ensure that the cutting disc is mounted correctly before

use.

u Let the tool run at no-load in a safe position for at least 30

seconds. If there is a considerable vibration or if any other

defect occurs, stop the tool and check it to determine the

cause.

u Do not use cutting discs for side grinding.

u Do not cut concrete, brick, tile or ceramic materials.

u Do not cut wood, plastic or synthetic materials.

u Do not cut cast-iron materials.

u Never cut magnesium materials.

u Do not cut electrically live material.

u Use this tool in a well-ventilated area. Do not operate the

tool near ammable liquids, gases or dust. Sparks or hot

chips from cutting or arcing motor brushes may ignite

combustible materials.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CS355 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CS355 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info