Bedienungsanleitung Black Decker EPC18 (Seite 7 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

472953

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

The charger automatically shuts off if the ambient

temperature becomes too high. The thermal cut out

operates only once and then requires complete

replacement.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch or two-speed on/off switch

2. Forward/reverse slider

3. Mode selector / torque adjustment collar

4. Chuck

5. Battery

6. Battery release button

g.C&D

7. Charger

8. Charger receptacle

9. Charger connector

10. Charger plug

Assembly

Warning! Before assembly, remove the battery from the tool.

Fittingandremovingthebattery(g.A)

u To t the battery (5), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (6) while at

the same time pulling the battery out of the receptacle.

Fittingthebatterycap(g.B)

Warning! Fit the cap (11) to the battery (5) for transportation

and storage.

Fitting and removing a drill bit or screwdriver bit

(g.E)

Warning! First remove the battery from the tool.

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Open the chuck by turning the front part (12) with one

hand while holding the rear part (13) with the other.

u Insert the bit shank (14) into the chuck.

u Firmly tighten the chuck by turning the front part (12) with

one hand while holding the rear part (13) with the other.

Removingandrettingthechuck(g.F)

u Open the chuck as far as possible.

u Remove the chuck retaining screw by turning it clockwise

using a screwdriver.

u Tighten an Allen key (15) into the chuck and strike it with

a hammer as shown.

u Remove the Allen key.

u Remove the chuck by turning it counterclockwise.

u To ret the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker EPC18 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info