Bedienungsanleitung Black Decker EPC186 (Seite 8 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

472960

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

ENGLISH

u Tighten an Allen key into the chuck and strike it with a

hammer as shown.

u Remove the Allen key.

u Remove the chuck by turning it counterclockwise.

u To ret the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Chargingthebattery(g.A&F)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. When charging the battery for the rst

time, or after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles, the battery

will attain full capacity. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Using the charger

u To charge the battery (7), remove it from the tool and slide

the charger receptacle (10) onto the battery.

u Plug in the charger (9).

The battery will become warm while charging. After approx.

3 hours of charging, the battery will be sufciently charged for

use in regular applications. After approx. 8-10 hours of

charging, the battery will be fully charged.

u Remove the charger receptacle from the battery.

Charger with charging plug

u To charge the battery, make sure that it is tted on the drill.

u Insert the charger plug (8) into the connector.

u Plug in the charger.

u Switch on at the mains.

After normal use, a charging time of 3 hours will provide

sufcient power for most applications.

However, further charging for up to 6 hours could signicantly

increase the use time, depending on the

battery and charging conditions.

u Disconnect the tool from the charger.

Warning! Do not use the tool while it is connected to the charger.

Selectingthedirectionofrotation(g.G)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selectingtheoperatingmodeortorque(g.H)

This tool is tted with a collar to select the operating mode and

to set the torque for tightening screws. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. The collar has a wide

range of settings to suit your application.

u For drilling in wood, metal and plastics, set the collar (3) to

the drilling position by aligning the symbol with the

marking (16).

u For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

- Set the collar (3) to the lowest torque setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Drillinginmasonry(g.H&I)

u For drilling in masonry, set the collar (3) to the hammer

drilling position by aligning the symbol with the marking

(16).

u Slide the speed selector (5) towards the front of the tool

(2nd gear).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker EPC186 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info