Bedienungsanleitung Black Decker FSM 1630S (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

526074

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

(Original instructions)

Steam cleaning

u Place a cleaning pad (6) on the oor with the ‘hook & loop’

side facing up.

u Lightly press the steam mop down onto the cleaning pad

(6).

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Press the Autoselect

button (2) till the required setting is

reached.

u Pulling the handle (4) back will activate the steam pump.

After a few seconds steam will start to come out of the

steam head.

Note: When rst lled or after running dry it can take up to 45

seconds for steam to be produced.

u It takes a few seconds for steam to enter the cleaning pad.

The steam mop will now glide easily over the surface to be

sanitised/cleaned.

u Push and pull the steam mop slowly across the oor to

thoroughly steam clean each section.

Note: During use you may turn off the steam pump by return-

ing the handle to the upright position, this convenient feature

will allow you to leave the steam mop for a short time so that

you may move items of furniture, then continue cleaning

without the need to switch the appliance off.

u When you have nished using the steam mop, return the

handle (4) to the upright position and turn it ‘OFF’ and

wait until the steam mop cools down. (approximately ve

minutes).

Caution! It is important to monitor the water level in the water

tank. To rell the water tank and continue to sanitise/clean,

return the handle (4) to the upright position and turn the steam

mop ‘OFF’. Unplug the unit from the electrical wall outlet,

remove and rell the water tank (3).

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop

with the handle (4) in the upright position when stationary and

make sure the steam mop is turned off when not in use.

Carpet refreshing

u Place a cleaning pad (6) on the oor with the ‘hook & loop’

side facing up.

u Lightly press the steam mop down onto the cleaning pad

(6).

u Place the carpet glider (7) on the oor.

u Lightly press the steam mop down onto the carpet glider

(7) until it clicks into place.

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Press the Autoselect

button (2) to the Wood/Laminate

setting.

u Pulling the handle (4) back will activate the steam pump.

After a few seconds steam will start to come out of the

steam head.

Note: When rst lled or after running dry it can take up to 45

seconds for steam to be produced.

u Push and pull the steam mop slowly across the carpet to

thoroughly refresh each section.

Note: During use you may turn off the steam pump by return-

ing the handle to the upright position, this convenient feature

will allow you to leave the steam mop for a short time so that

you may move items of furniture, then continue cleaning

without the need to switch the appliance off.

u When you have nished using the steam mop, return the

handle (4) to the upright position and turn it ‘OFF’ and

wait until the steam mop cools down. (approximately ve

minutes).

Caution! It is important to monitor the water level in the water

tank. To rell the water tank and continue to sanitise/clean,

return the handle (4) to the upright position and turn the steam

mop ‘OFF’. Unplug the unit from the electrical wall outlet,

remove and rell the water tank (3).

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop

with the handle (4) in the upright position when stationary and

make sure the steam mop is turned off when not in use.

After use (Fig. I)

u Return the handle (4) to the upright position and turn the

steam mop ‘OFF’,

u Wait until the steam mop cools down. (approximately ve

minutes)

u Unplug the steam mop from the electrical wall outlet.

u Empty the water tank (3).

u Remove the cleaning pad (6) and wash it ready for next

use. (Take care to follow the wash care instructions

printed on the cleaning pad).

u Wrap the supply cable around the cable tidy hooks (8 &

9).

Note: The top cable tidy hook (11) rotates to easily release the

cable ready for next use.

u Clip the supply cable onto itself using the cable tidy clip

(22) close to the plug.

Note: With the handle (4) in the upright position, the cable

neatly wrapped around the cable tidy hooks (8 & 9) and

secured with the cable tidy clip (22) your steam mop will stand

on its own for storage. Alternatively there is a hanging bracket

built into the hand grip which will allow your steam mop to

be hung from a suitable hook on the wall. Always ensure

that your wall hook is capable of supporting the weight of the

steam mop safely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker FSM 1630S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info