Bedienungsanleitung Black Decker FSM1630 T1 (Seite 7 von 23) (Französisch)

586622

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

ENGLISH

(Original instructions)

Autoselect

Technology (Fig. J)

This steam mop is tted with an Autoselect

button (2)

which shows various cleaning applications. They are used to

select the correct operating mode for your particular cleaning

operation.

Using Autoselect

, choose from one of the following applica-

tions by pressing the autoselect button (2) until the required

setting is selected:

Wood/Laminate

Stone/Marble

Tiles/Vinyl

The steam mop will select the correct volume of steam

required for your particular cleaning operation.

Note: Always check you are using the correct setting before

using your steam mop. For convienience the steam mop will

remember the last setting you chose.

Steam burst (Fig. I)

The steam mop is equipped with a steam bust button to aid in

the removal of stubborn marks and stains.

u During use, press the steam bust button (21) to apply

extra cleaning power.

Note: The stem burst will last for 10 seconds then the stem

mop will return to the chosen setting.

Hints for optimum use

General

Caution! Never use the steam mop without rst attaching a

cleaning pad.

u During use you can use the cable mamagement clip (11)

to keep your cable out of the way of the work area..

u Always vacuum or sweep the oor before using the steam

mop.

u The easiest way to use the machine is to tilt the handle to

a 45˚ angle and clean slowly, covering a small area at a

time.

u Do not use chemical cleaners with your steam mop. To

remove stubborn stains from vinyl or linoleum oors, you

can use the steam burst button to apply extra steam to

the area or pre-treat with a mild detergent and some water

before using the steam mop.

Steam cleaning

u Place a cleaning pad (6 or 7) on the oor with the ‘hook &

loop’ side facing up.

u Raise the steam mop off the resting mat (8) and lightly

press it down onto the cleaning pad (6 or 7).

u Place the steam mop on the resting mat.

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Press the Autoselect

button (2) till the required setting is

reached.

u Pulling the handle (4) back will activate the steam pump.

After a few seconds steam will start to come out of the

steam head.

u It takes a few seconds for steam to enter the cleaning pad.

The steam mop will now glide easily over the surface to be

sanitised/cleaned.

u Push and pull the steam mop slowly across the oor to

thoroughly steam clean each section.

Note: During use you may turn off the steam pump by return-

ing the handle to the upright position, this convenient feature

will allow you to place the steam mop on the resting mat for

a short time so that you may move items of furniture, then

continue cleaning without the need to switch the appliance off.

u When you have nished using the steam mop, return the

handle (4) to the upright position and turn it ‘OFF’, place it

on the resting mat (8) and wait until the steam mop cools

down. (approximately ve minutes)

Caution! It is important to monitor the water level in the water

tank. To rell the water tank and continue to sanitise/clean,

return the handle (4) to the upright position and turn the steam

mop ‘OFF’. Unplug the unit from the electrical wall outlet,

remove and rell the water tank (3).

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop on

the resting mat (8) with the handle (4) in the upright position

when stationary and make sure the steam mop is turned off

when not in use.

Carpet refreshing

u Place a cleaning pad (6 or 7) on the oor with the ‘hook &

loop’ side facing up.

u Raise the steam mop off the resting mat (8) and lightly

press it down onto the cleaning pad (6 or 7).

u Place the carpet glider (9) on the oor.

u Lightly press the steam mop down onto the carpet glider

(9) until it clicks into place.

u Place the steam mop on the resting mat. (8)

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Press the Autoselect

button (2) to the Wood/Laminate

setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker FSM1630 T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker FSM1630 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info