Bedienungsanleitung Black Decker GK1630T T3 (Seite 11 von 20) (Englisch)

584940

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

The new connection system does not

release the operator of the tool from the

safety precautions and safe working

practices given in the manual. Particular

attention is drawn to the fact that this

connection system is ‚weather resistant‘,

but not suitable for immersion,

submersion or being subjected to water

jets. Take care to prevent the cable from

lying in or trailing through pools of water

or from splashing with hose pipes.

The following items are available:

A6615 20 m cable, socket, 13 Amp plug

A6616 20 m cable, socket, 13 Amp plug and

Cable Tidy frame

A6617 30 m cable, socket, 13 Amp plug and

Cable Tidy frame

A6613 40 m cable, socket, 13 Amp plug and

Cable Tidy reel

Existing cable systems

Your tool either comes with a cable attached

(the cat. no. ends with a C) or with a male connector

built into the tool. If you already own an outdoor

cable system with the old female connector shown

below, we recommend that you replace this

connector with the new female connector, which is

available from most major DIY outlets and from

Black & Decker service centres (cat. no. A6624S).

old female connector new female connector

Follow the instructions supplied with the connector.

If in doubt, consult a qualified electrician.

Existing outdoor tools

To connect existing Black & Decker outdoor tools

to the new system, you will need an adaptor (see

below), which is available as an accessory from

most major DIY outlets and from Black & Decker

service centres (cat. no. A6623S).

This adaptor is only suitable for products

rated up to 500 W. It is not recommended

for use with hover mowers, rotary mowers

with grass collection, chainsaws, shredders

and blower vacs. Please contact your local

service centre if you need further advice.

Fitting your own extension cable

◆When making your own extension cable,

fit a 13 Amp plug to one end of the cable

(see „Mains plug replacement“) and a female

connector to the other end. For wiring

instructions, see those supplied with the

female connector.

◆A male connector (see below) is already attached

to the power supply cable on your tool. It is

non-rewireable and should not be removed. If

the connector is damaged and needs

replacement, take the tool to a Black & Decker

service centre.

female connector male connector

Never wire an extension cable with

anything other than the female connector

supplied and a 13 Amp BS1363A

approved plug with the recommended

fuse. Never wire a male connector to the

extension cable. Never wire an extension

cable with a plug of any kind at each end

of the cable. This is extremely dangerous

and results in the pins being live, which

may cause a fatal electric shock.

Fitting the female connector

◆To remove the cover, unscrew the fixing screw

until it is free of the nut which is located in the

hexagonal recess on the underside of the

connector. Take care not to lose the nut if it

falls out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GK1630T T3 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GK1630T T3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info