Bedienungsanleitung Black Decker GK1630T (Seite 12 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

55632

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

When supported at one end:

u First cut one third up to avoid splintering and second, cut

down to prevent splintering.

Whenonaslope(g.L):

u Always stand on the uphill side.

Whenattemptingtocutalogontheground(g.L):

u Secure the workpiece using chocks or wedges. The user

or a bystander should not steady the log by sitting or

standing on it. Make sure that the saw chain does not

contact the ground.

Whenusingasawhorse(g.M):

This is strongly recommended whenever possible.

u Position the log in a stable position. Always cut on the

outside of the saw horse arms. Use clamps or straps to

secure the workpiece.

Troubleshooting

Problem Possible cause Possible

sollution

Tool will not start Lock button not

pressed.

Press the lock

button.

Front guard in the

brake position

Reset front guard

Blown fuse Replace fuse

Tripped RCD Check RCD

Mains lead not

connected

Check mains

supply

Chain does not

stop instantly

when the tool is

switched off

Chain tension is

too slack

Check chain

tension

Bar/chain appear

hot/smoking

Oil tank empty Check oil tank

level

Oil hole blocked

on chain bar

Clean oil hole

Chain tension is

too tight

Check chain

tension

Guide bar

sprocket

nose needs

greasing

Oil the guide bar

sprocket nose

Problem Possible cause Possible

sollution

Chainsaw does

not cut well

Chain on

backwards

Check/modify

chain direction

Sharpen

Chainsaw not

using oil

Debris in tank Empty oil from

tank and replace

Oil hole in cap

blocked

Remove debris

from hole

Debris in chain

bar

Remove debris

and clean the

chain bar

Debris in oil outlet remove debris

Maintenance

Regular maintenance ensures a long effective life for the

tool. We recommend you make the following checks on a

regular basis.

Warning! Before performing any maintenance on power tools:

u Switch off and disconnect the tool from the mains supply.

Oil level

The level in the reservoir should not be allowed to fall below

a quarter full.

Sawchainandguidebar(g.G)

u After every few hours of use and before storage, remove

the guide bar (7) and the saw chain (6) and clean them

thoroughly.

u Make sure that the guard is clean and free from debris.

u On reassembling, turn the guide bar (7) through 180° and

oil sprocket nose via the sprocket lubrication hole (17).

This ensures an even distribution of wear around the

guide bar rails.

Saw chain sharpening

If you are to get the best possible performance from the tool

it is important to keep the teeth of the saw chain sharp.

Guidance for this procedure is found on the sharpener

package. For this purpose we recommend the purchase of

the Black & Decker saw chain sharpening kit (available from

Black & Decker service agents and selected dealers).

Replacing worn out saw chains

Replacement saw chains are available through retailers or

Black & Decker service agents. Always use genuine spare

parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GK1630T Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GK1630T

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info